Lincoln Electric IM10024 manual K325 TC-3 Travel Carriage

Page 17

A-10

INSTALLATION

A-10

 

 

 

K325 - TC-3 TRAVEL CARRIAGE

The TC-3 travel carriage is available in two models. Both are “High Capacity” and suitable for multiple arc welding.

K325HC5”-Sto(Standard70”/min (127mm- 952:1 toratio)1.88M/mim)

K325-HC15”-F to(High270”/minSpeed(381mm- 254:1toratio)6.86M/min) Although the carriages can be set for speeds

NOTE: down to zero, speed variations increase dra- matically with uneven loading when operated below the recommended minimum speeds.

The maximum amount of equipment that a K325 car- riage can safely carry is shown in Table A.2

It is important when mounting wire reels,and other equipment to the TC-3 Travel Carriage that there is a minimum of overhung weight. The Wire Drive mount- ings are to be such that the heads are within 19” (483mm) from the front of the carriage as shown in Figure A.5.

FIGURE A.5

19”

(483mm)

TABLE A.2 - MAXIMUM EQUIPMENT LOAD FOR TC-3

MULTIPLE ARC OPERATION

TANDEM TWINARC®

Two MAXsa™

 

Three MAXsa™

Two MAXsa™

 

Wire Drives and Controls

 

Wire Drives and Controls

Wire Drives and Controls

Two Wire Reels

 

Three Wire Reels

Four Wire Reels(60# Coils)

(60 # Coils)

 

(60# Coils)

Centrally Located

Two K29

 

Three K29

Two K29

Vertical Adjusters

 

Vertical Adjusters

Vertical Adjusters

Two K96

 

Three K96

Two K96

Horizontal Adjusters

 

Horizontal Adjusters

Horizontal Adjusters

Flux Hopper

 

Flux Hopper

Flux Hopper

150# of Auxiliary Equipment

 

No Auxiliary

No Auxiliary

Centrally Located over TC-3

 

Equipment

Equipment

MAXsa™ 22 & 29 WIRE DRIVES

Image 17
Contents MAXsa 22 & 29 Wire Drives California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionLES Machines À Souder À Thank You Table of Contents 1PRODUCT DESCRIPTIONA-1 MAXsa 22 & 29 Wire DrivesGeneral Information DESIGNClosed-loopFEATURESspeedcontrol- .MAXsaFigure A.2 Location of MAXsa 29 Components InstallationWidth Depth SpecificationsHigh Frequency Protection NON-STANDARD Safety InformationLocation and Mounting System Connections Mounting DimensionsFigure A.3 ConfigurationTable A.1 Drive Roll Kits Wire Feed MechanismGear Ratio Conversion Kits See Table A.1 Output Cable Guidelines Remote Sense Lead SpecificationsElectrode Connections K325HC5-StoStandard70/min 127mm- 9521 toratio1.88M/mim K325 TC-3 Travel CarriageFigure A.6 Wire Drive Mounting InstallationFigure A.10 Inclined Operation Inclined Operation of TC-3Carriage Bearing Tracking Drive Gear TrackingMaxsa 22 & 29 Wire Drives Head Position AdjustmentsOperation Starting TechniquesFigure B.1 Feed Head Adjustment Search AccessoriesFollow these steps Connect the lug on the electrode cables from Model K226-T K226 Contact AssemblyLong Stickout Extension Current RatingsOperation Loading of WireK148 Nozzle Installation K285 Concentric Flux Cone K285 Installation to the K148Figure C.10 K285/K149 K285 installation with the K129 K285 Installation with K149With K148 or K148/K149 combination After K285 Used in Horizontal Fillet ApplicationsWith the K129 Tiny Twin-Arc No zle After K285 in Deep Narrow Gap ApplicationsAdjustment and Locking K29 Vertical Head AdjusterInstallation See Figure C.14 K96 Horizontal Head AdjusterK129 Tiny Twinarc KIT For .045 through 5/641.0-2.0mm WiresFigure C.17 Nozzle InstallationFigure C.18 K225 Twinarc Components K225 Submerged ARC Twinarc KITFigure C.20 Nozzle Installation See Figure C.18Tiny Twinarc K281 Solid Wire Straightener forWire Loading and Adjustment Sense Lead Fuse MaintenanceElectric Shock can kill HOW to USE Troubleshooting Guide TroubleshootingOutput Problems Diagrams L13370 Dimension PrintPrecaucion Warnung