Lincoln Electric IM10024 manual Operation, Starting Techniques, Head Position Adjustments

Page 21

B-1

OPERATION

B-1

 

 

 

ROUTINE OPERATION

Once the procedures and parameters are properly set at the controller the operator should be able to make production welds without changing those settings. A typical weld sequence is as follows:

1. Before starting, make sure that:

a. There is enough wire on the reel(s) to finish the weld.

b. The flux hopper is filled with new or proper- ly screened flux.

2. Energize the power source and wait for it to stabi- lize (all Status LEDʼs Green).

3. Position the Wire Feed Head at the start of the weld. Be sure the TC-3 Carriage or travel mecha- nism is set to move in the proper direction

4. Set the travel switch for “Automatic Travel” if the “Hand Travel” position was used to position the feed head in Step 3.

STARTING TECHNIQUES

1.- refers to starting the weld with the WireHot StartingDrive head stationary and the wire not touch- ing the workpiece.

a. Always cut the end of the wire to a sharp point.

b. Press Feed Forward until the wire touches the work piece and the flux hopper acti- vates to put flux around the starting point.

c. Press Feed Reverse to retract the wire 1/8” to 1/4” (3.2-6.4mm).

d. Use the Set-Up menu of the MAXsa™ 10 or remote controller to determine whether the travel will begin with Start Button pressed or with weld current (preferred).

e. Press the START button to initiate the weld. f. Press the STOP button to begin the stop-

ping sequence.

h. If necessary, press the Feed Reverse to move the electrode out of the way.

2.- refers to starting the weld afterOn-thethe-flytravelStartingbegins to get a “scratch” start. Normally this type of starting requires the use of a ʻrun-onʼ tab to insure proper weld deposition at the beginning of the weld.

a. Use the Set-Up Menue of the MAXsa™ 10 to set the travel to start with the START button.

b. Follow the Hot Starting procedure.

- refers to starting the weld with the WireColdDriveStartingHead stationary and the electrode touching the work.

a. This procedure is not recommended for the Power Wave® AC/DC 1000 / MAXsa™ 22 & 29 WIRE DRIVES combinations but may work OK with smaller diameter wires and proper setting of the Start parameters.

b. Follow Hot Starting procedure but omit “step c”.

HEAD POSITION ADJUSTMENTS

The MAXsa™ 22 & 29 WIRE DRIVES can be easily adjusted to any weld position. The most often used adjustments are available on both the MAXsa™ 22 and the MAXsa™ 29 Wire drives. See Figure B.1 Turn the Cross Seam Adjuster (MAXsa™ 29) to keep the arc in the joint as necessary. With a MAXsa™ 22, a K96 or some other means of horizontal adjustment is recommended. See Figure B.2

The entire Wire Drive can be moved into or out of the Mounting Bracket (M6789). If using a K29 Vertical Lift Adjuster it can be locked in either the horizontal or vertical position once the vertical position is set. See Figure B.3.

If the Wire Drive is rotated to a position where the faceplate is upside down, the contact nozzle and the wire straightner and guide tubes will need to be reversed. The polarity of the motor will also need to be changed so the wire feeds in the proper direction. See the Installation Section,

polarityConfiguration. for instructionsChangingon changingthe Wirethe Drivemotor

MAXSA™ 22 & 29 WIRE DRIVES

Image 21
Contents MAXsa 22 & 29 Wire Drives California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionLES Machines À Souder À Thank You Table of Contents 1PRODUCT DESCRIPTIONA-1 MAXsa 22 & 29 Wire DrivesGeneral Information DESIGNClosed-loopFEATURESspeedcontrol- .MAXsaFigure A.2 Location of MAXsa 29 Components InstallationWidth Depth SpecificationsNON-STANDARD Safety Information Location and MountingHigh Frequency Protection System Connections Mounting DimensionsFigure A.3 ConfigurationWire Feed Mechanism Gear Ratio Conversion Kits SeeTable A.1 Drive Roll Kits Remote Sense Lead Specifications Electrode ConnectionsTable A.1 Output Cable Guidelines K325HC5-StoStandard70/min 127mm- 9521 toratio1.88M/mim K325 TC-3 Travel CarriageFigure A.6 Wire Drive Mounting InstallationFigure A.10 Inclined Operation Inclined Operation of TC-3Carriage Bearing Tracking Drive Gear TrackingMaxsa 22 & 29 Wire Drives Head Position AdjustmentsOperation Starting TechniquesFigure B.1 Feed Head Adjustment Accessories Follow these stepsSearch Connect the lug on the electrode cables from Model K226-T K226 Contact AssemblyLong Stickout Extension Current RatingsLoading of Wire K148 Nozzle InstallationOperation K285 Concentric Flux Cone K285 Installation to the K148Figure C.10 K285/K149 K285 installation with the K129 K285 Installation with K149With K148 or K148/K149 combination After K285 Used in Horizontal Fillet ApplicationsWith the K129 Tiny Twin-Arc No zle After K285 in Deep Narrow Gap ApplicationsAdjustment and Locking K29 Vertical Head AdjusterInstallation See Figure C.14 K96 Horizontal Head AdjusterK129 Tiny Twinarc KIT For .045 through 5/641.0-2.0mm WiresFigure C.17 Nozzle InstallationFigure C.18 K225 Twinarc Components K225 Submerged ARC Twinarc KITFigure C.20 Nozzle Installation See Figure C.18K281 Solid Wire Straightener for Wire Loading and AdjustmentTiny Twinarc Maintenance Electric Shock can killSense Lead Fuse HOW to USE Troubleshooting Guide TroubleshootingOutput Problems Diagrams L13370 Dimension PrintPrecaucion Warnung