Lincoln Electric IM10031-A manual Power Source to LN-25 PRO, Across the ARC SET-UPS, Description

Page 16

A-7	INSTALLATION	A-7

POWER SOURCE TO LN-25™ PRO

CAbLE CONNECTION DIAGRAMS

ACROSS THE ARC SET-UPS

CCPower Sources with Output Terminals Always Hot (See Figure A.5)

	CC Power Source
	Classics
	Classics		FIGURE A.5
	Big Red’s		FIGURE A.5
	Big Red’s
	Eagle 10,000 Plus
	Pipeliner 200D Without Wire Feed module
	SAE’s Without CV Adapter		LN-25™ PRO
	SAE 400 with CV adapter	Electrode	LN-25™ PRO
	SAE 400 with CV adapter	Electrode
	Engine Driven welder with
	Wire Feed Module
				Work clip
		Work

If the power source has a Remote/Local switch, place the switch in the Local position.

Place the CV/CC switch in the feeder in the "CC" posi- tion.

CV Power Sources with Stud Connectors and Remote/Local Switch (See Figure A.6)

CV-655
DC-400
DC-600
DC-655	Electrode
V450-Pro
SAE 400 with CV adapter
Engine Driven welder with
Wire Feed Module	Work
Ranger 250 GXT	Work

Place the power source Remote/Local switch in the Local position.

Place CV/CC switch in the feeder in the "CV" position.

	K#		Description

	K2613-1		LN-25™ PRO
	K2613-2		LN-25™ PRO Extra Torque
	KP1695-XX
	KP1696-XX		Drive Roll Kit
	KP1697-XX
	See Magnum Literature		Welding Gun
			CC power Source
	K1803-1		Welding Cables


FIGURE A.6

	LN-25™ PRO
			Work clip

	K#		Description

	K2613-1		LN-25™ PRO
	K2613-2		LN-25™ PRO Extra Torque
	KP1695-XX
	KP1696-XX		Drive Roll Kit
	KP1697-XX
	See magnum Literature		Welding Gun
			CV power Source
	K1803-1		Welding Cables

LN-25™ PRO

Image 16

Contents LN-25 Tmpro Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents Installation Technical Specifications LN-25 PRO K2613-1, K2613-2Wire SIzES LN-25 PROSafety Precautions LocationHigh Frequency Protection Weld CAbLE SIzE3INSTALLATIONA-3 Power SourceWire Feeder Analog Control CAbLE K1797-xx CAbLE Connections Function Pin Wiring Shielding GAS Connection Procedure to Install Drive Rolls and Wire Guides Wire Drive ConfigurationChanging the GUN Receiver bUSHING Pressure ARM Adjustment Loading Spools of WireGUN Connection Fe, CrNiAcross the ARC SET-UPS Power Source to LN-25 PRODescription Figure A.7 9INSTALLATIONA-9 Figure A.9Safety Precautions OperationGeneral Description Case Front Controls See Figure b.1 Figure b.1Wire Feed Speed KNOb Wire Feed Speed, CV OperationMinimum Arc Volts Maximum WFS Extra TorquePolarity LED Internal Controls Figure b.2Step Trigger Interlock Switch Internal Controls DescriptionCold Feed PUSHbUTTON Step TriggerConstant Current Wire Welding Figure b-3Itemdescription Rear ControlsPOWER-UP Sequence GAS Purge PUSHbUTTONFlow Meter Liter/MinAccessories Factory Installed EquipmentDrive Roll Kits Electrode SIzEOn at all times Accessories K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Maintenance Routine MaintenancePeriodic Maintenance CALIbRATION SpecificationWire Feed Speed Validation To change the wire feed speed calibration See Figure D.2Model gearing BOARD LN-25 PROTROUbLESHOOTING Electric Shock can killPRObLEMS SymptomsPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Diagrams Enhanced DiagramDimension Print Precaucion Warnung