Friedrich WY09, WY12, WS12 operation manual Installation requirements, Sleeve installation

Page 10
Installation requirements

Installation requirements

STEP 1 The WSD SLEEVE should be positioned so that the DRAIN EXTENSION extends a minimum of 916" beyond the OUTSIDE WALL (See Figure 7).

STEP 2 The WSD SLEEVE must extend a minimum of ⅞" beyond the INSIDE WALL.

STEP 3 The WSD SLEEVE must be installed level side to side.

STEP 4 The WSD SLEEVE must also be installed with a downward tilt toward the outside of the building. If a level is placed so that it rests on the FRONT and BACK UNIT REST as shown in Figure 8, a properly installed unit provides a ½ bubble slope to the outside of the building.

FIGURE 8

Raised

Ledge

Back Unit Rest

Level

Sleeve installation

STEP 1 After unpacking the WSD SLEEVE from the carton, remove the FRONT PANEL. Place the WSD SLEEVE in the wall opening following the instructions given in the INSTALLA- TION REQUIREMENTS. Attach the SLEEVE to the INSIDE WALL by driving two #12A x 2" screws in each side of the SLEEVE (see Figure 7). Shim at the top of the SLEEVE, midway between the sides. Drive one #12A x 2" screw in the top of the sleeve, close to the shim. Install screws from inside the SLEEVE. If the wall opening is not framed with wood, use expansion anchor bolts or molly (toggle) bolts (not provided).

Please note that there will be an excess of two #12Ax2" screws that will not be used.

STEP 2 Once the SLEEVE has been installed, check the LEVEL again to be sure the ½ bubble downward tilt is maintained. Apply shims, if required, to maintain the proper slope.

STEP 3 Caulk the perimeter of the entire opening on the inside and the outside between the SLEEVE and the WALL.

STEP 4 The front panel removed in Step 1 above must be remoun- ted back in place if masonry work is to be done and/or if the "WallMaster" CHASSIS is to be installed at a later date.

Front Unit Rest

Slope

NOTICE

SLEEVE projections and leveling precautions must be observed to prevent the entry of water into the room.

10

Image 10
Contents Thru-the-wall Air Conditioners and Heat PumpsTABLE OF CONTENTS WELCOME to years of economical comfort Electrical DataTo set the timer To adjust temperatureTo adjust fan speed To start unitTo start unit See Figure 3, page Using the remote controlDigital Control Panels Automatic component protectionDECORATIVE FRONT How to cover inner weather panel holes How to change airflow directionElectrical requirements To test your power supply cord Troubleshooting tips and home maintenancePower cord information Never use an extension cordFrosting of the indoor coil Installation instructions for WSD sleeveCleaning the decorative front Mounting hardware providedInstallation requirements Sleeve installationExcessive Weight Hazard Cut/SeverALTERNATE DRAIN KITS CONDENSATE REMOVAL WS, WE AND WY MODELSMoving Object Hazard FIRST YEAR LIMITED WARRANTYWALLMASTER THRU-THE-WALLAIR CONDITIONERS SECOND THROUGH FIFTH YEAR115-Volt WS08, WS10, WS14 Unidades de aire acondicionado y bombas de calorThru-the-wall Instrucciones de instalación y funcionamientoOperación Índice de contenidoIntroducción Instrucciones de instalación para la carcasa WSDDatos eléctricos BIENVENIDO a muchos años de comodidad y economíaADVERTENCIA Para activar MoneySaver modelos WY/WE Para configurar el reloj horarioPara configurar el temporizador Para poner en marcha la unidadPara poner en marcha la unidad vea Fig Uso del mando a distanciaPANEL DE CONTROL DE LA UNIDAD Para configurar el modo de funcionamientoMando a distancia del modelo calor-fríoWY/WE Como limpiar el filtroFigura Para configurar el temporizadorDesenchufe el acondicionador de aire ADVERTENCIACómo cambiar la dirección del flujo de aire Requisitos eléctricosNo funciona Cable de alimentaciónNo enfría ADVERTENCIAHerramienta de montaje suministrada ADVERTENCIAPara limpiar la cubierta decorativa Preparación de la paredRequerimientos para la instalación AVISOInstalación de la base de empotraje Riesgos de cortadas/amputaciones PRECAUCIONPeligro de peso excesivo PRECAUCIONDK Equipo de drenaje ADVERTENCIAEquipos opcionales para drenaje IDK Equipo para drenaje interiorWALLMASTER Garantía limitada para unidades de aireacondicionado de tipo ventana EL PRIMER AÑOThru-the-wall Climatiseurs et pompes à chaleurManuel dinstallation et de fonctionnement 115-Volts WS08, WS10, WS14Table des matières Directives pour linstallation du caisson WSDDirectives dinstallation du châssis WallMaster IntroductionAVERTISSEMENT BIENVENUE à des années de confort économiqueDonnées électriques AVERTISSEMENTPour activer MoneySaver modèles WY/WE Réglage de lhorlogeRéglage de la minuterie Pour mettre lappareil en marchePour mettre l’unité en marche voir figure Utilisation de la télécommandeProtection automatique des composants Pour régler le mode de fonctionnementPour régler la minuterie Nettoyage du filtreComment changer la direction de lécoulement dair Exigences électriquesPas de refroidissement Guide de dépannage et maintenanceAVERTISSEMENT Lappareil ne fonctionne pasNettoyage du panneau avant décoratif AVERTISSEMENTGivre sur le serpentin interne Matériel fourni pour le montageInstallation de lenveloppe Besoins lors de linstallationAVIS Danger concernant un poids excessif Coupure/EntaillerDK kit de vidange Danger lors du déplacementAutre kits de vidange IDK kit de vidange intérieurPREMIÈRE ANNÉE Garantie limitée - Climatiseurs WallMasterTHRU-THE-WALLFriedrich DEUXIÈME À CINQUIÈME ANNÉEPage Page Page Page FRIEDRICH AIR CONDITIONING CO SAN ANTONIO, TX
Related manuals
Manual 13 pages 18.94 Kb

WS12, WY09, WY12 specifications

Friedrich is a well-known name in the HVAC industry, particularly recognized for its innovation and quality in providing efficient and reliable cooling solutions. The Friedrich WY09, WS12, WY12, WS15, and WE15 models are a part of their lineup that reflects cutting-edge technology, robust performance, and a commitment to energy efficiency.

The Friedrich WY series, particularly models WY09 and WY12, are window air conditioners designed to provide powerful cooling in compact spaces. They feature advanced inverter technology that allows them to adjust the compressor speed based on the cooling demand, resulting in quieter operation and reduced energy consumption. The WY series is equipped with a programmable thermostat and multiple fan speeds, giving users greater control over their indoor climate. Furthermore, these units often come with a 24-hour timer and a remote control for added convenience.

On the other hand, the Friedrich WS series, including WS12 and WS15 models, is designed for wall-mounted installation, making them an excellent option for homeowners looking to save window space while still enjoying excellent cooling capabilities. These models offer high energy efficiency ratings, which can significantly reduce electricity bills. The WS series incorporates features like easy-to-use digital controls, energy saver modes, and filtration systems that improve air quality by capturing dust and allergens.

The WE15 model caters to those who need robust performance in larger spaces. This unit combines substantial cooling power with features found in smaller models, like smart technology integration and Wi-Fi connectivity. This allows users to control their air conditioning remotely via smartphone apps, making it easy to adjust settings and manage energy use from anywhere.

All of these Friedrich models prioritize user convenience and efficiency. Many come with washable filters, reducing maintenance costs and promoting better air quality. Additionally, they're designed with a focus on durability and low noise levels, ensuring comfort and peace in residential and commercial settings alike.

In summary, Friedrich's WY09, WS12, WY12, WS15, and WE15 models exemplify reliability and innovation in air conditioning technology. They are engineered to meet varying cooling demands while maximizing energy efficiency, making them ideal choices for those looking for effective climate control solutions. Whether installed in a window or a wall, these air conditioners deliver the performance and features necessary for modern living.