Craftsman 919.167242 owner manual Storage, To Replace Regulator, Regulator Arrow

Page 18

To Replace Regulator

1.Release all air pressure from air tank. See "To Drain Tank" in the Maintenance section.

2.Release all air pressure from air tank. See "To Drain Tank" in the Maintenance section.

3.Using an adjustable wrench remove the gauges and quick connect from the regulator.

4.Remove the regulator.

5.Apply pipe sealant tape to the nipple on the standpipe.

6.Assemble the regulator and orient as shown.

NOTE: Arrow indicates flow of air. Make sure it is pointing in the direction of air flow.

Regulator

Arrow

7.Reapply pipe sealant to gauges and quick connect.

8.Reassemble gauges and quick connect. Orient gauges to read correctly. Tighten quick connect with wrench.

STORAGE

Before you store the air compressor, make sure you do the following:

1.Review the "Maintenance" section on the preceding pages and perform scheduled maintenance as necessary.

2.Set the On/Auto/Off lever to "OFF" and unplug unit.

3.Turn the regulator counterclockwise and set the outlet pressure to zero.

4.Remove the air tool or accessory.

5.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately

20 psi. Release safety valve ring.

6.Drain water from air tank by opening drain valve on bottom of tank.

Risk of Bursting. Water will

condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

7.After the water has been drained, close the drain or drain valve.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled.

8.Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind them loosely around the compressor handle. (If so equipped)

9.Store the air compressor in a clean and dry location.

A08598

18- ENG

Image 18

Contents AIR Compressor Table of Contents Specification Chart Safety Guidelines DefinitionsImportant Safety Instructions Location away from compressor Spray area. An additional length of hoseExplosion May be required Fire, do not allow the compressor toAttachments & Accessories What Could HappenElectrical codes Safety equipment must be properlyAccordance with national and local Electrical Grounding Failure to provideHot for several minutes after operation Or attempt maintenance until unit hasResult in serious burns Do not reach around protective shroudsHazard Glossary AccessoriesAccessories Duty CycleTools Required for Assembly AssemblyContents of Carton Installing Handles Wheels, and Molded Foot BumpersGrounding Instructions InstallationLocation of the Air Compressor Plug Grounded Outlets Grounding PinExtension Cords Voltage and Circuit ProtectionDescription of Operation OperationKnow Your Air Compressor RegulatorDrain Valve How to StopBefore Starting Break-in Procedure Check ValveHow to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain TankOutlet Tube Nut Check Valve Service and AdjustmentsTo Replace or Clean Check Valve Screwdriver Open position nothing is visibleStorage To Replace RegulatorRegulator Arrow Troubleshooting Pressure reading Problem Cause Correction Contenido GarantíaGarantía Total DE UN AÑO DEL Compresor DE Aire Resultar en lesiones menores o Definiciones DE Normas DE SeguridadModelo Nº 919.167242 ModeradasInstrucciones Importantes DE Seguridad Guarde Estas InstruccionesCómo prevenirlo Advertencia Riesgo de Explosión Qué puede occurrir Cómo prevenirloA08598 30- SP Advertencia Riesgo de Quemaduras Qué puede occurrir Advertencia Riesgo de Caída Qué puede occurrirAdvertencia Riesgo de Operación Insegura Qué puede occurrir Ciclo DE Servicio GlosarioAccesorios AccesoriosHerramientas requeridas para el ensamblado EnsambladoContenido del embalaje Instalación de manijas, ruedas y pie moldeado de reboteInstalación Cómo Preparar LA UnidadUbicación del compresor de aire Cables de extensión eléctrica Protección del voltaje y del circuitoDescripción de operaciones OperaciónConozca su compresor de aire Presión de salida TanqueCómo utilizar su unidad Antes de poner en marchaCómo detenerla Antes de cada puesta en marcha Cómo poner en marchaCómo verificar la válvula de seguridad MantenimientoResponsabilidades del cliente Cómo drenar el tanqueTubo de salida Tuerca Servicio Y AjustesPara reemplazar o limpiar la válvula reguladora Destornillador En posición abierta nada es visiblePara reemplazar el regulador Regulador FlechaAlmacenaje Riesgo Guía DE Diagnóstico DE ProblemasProblema Causa Corrección Alguna porque se debilitaráDesciende cuando El motor no funciona Product replacement if your covered product cant be fixed Repair Protection AgreementsGet it fixed, at your home or ours