Xantrex Technology SW 3000 user service System Start-up Check Viewing the Firmware Revision Number

Page 29

	Operating The Freedom SW 3000
System Start-up Check	Viewing the Firmware Revision Number

IMPORTANT: Review the “Important Safety Instructions” on page iv before operating the inverter/charger.

To test inverting and charging from the Freedom SW 3000 front panel:

1.Disconnect AC power from inverter input by opening the breaker or disconnect. Press the Inverter Enable button on the Freedom SW 3000. The Inverter On light illuminates.

2.Place a load on the inverter. For example, plug a 100 watt light bulb into an outlet that the inverter is powering and make sure it works. The inverter should run the load using battery power.

3.To test the charger, reconnect the AC input power to allow AC to the AC input. The AC/Charger On light should illuminate after a brief delay. Any AC loads previously powered by the inverter will also work at this time.

4.Remove the AC input power. The inverter/charger should transfer to invert mode immediately. (The transfer relay will make a clicking sound and the Inverter On light will illuminate.) Loads should continue to operate uninterrupted.

If any part of this test fails, determine the cause before using the unit. Consult the “Troubleshooting” chapter starting on page 45.

You may need to view the firmware revision number of the Freedom SW 3000 when troubleshooting the unit with authorized service personnel.

To view the firmware revision number:

1.On the Select Device menu, use the down arrow button to highlight System and press Enter.

The System Settings menu appears.

2.Press the down arrow button to highlight View Device info and press Enter.

The Device Info screen appears.

3.Press the down arrow button until the Freedom SW 3000 screen appears.

The number opposite “F/W Rev.” is the firmware revision number.

4.Press Exit to return to the System Settings menu.

975-0545-01-01

15

Image 29

Contents Freedom SW Sine Wave Inverter/Charger Page Exclusion for Documentation About Xantrex TrademarksDate and Revision Document Part NumberStatement of Hazard About This GuideRelated Information Electrical Shock Hazard Important Safety InstructionsExplosion Hazard Fire and Burn HazardPrecautions When Working With Batteries Precautions When Placing the Inverter/Charger Precautions When Preparing to ChargeExposure to Chemicals and Gases Hazard Risk of Damage to the INVERTER/CHARGERLimitations on USE RegulatoryContents Page Page Page Materials List IntroductionAbout the Freedom SW Inverter/Charger Premium Power and Ease of UseCharging How the Freedom SW 3000 Inverter/Charger WorksInverting Xanbus System Typical Xanbus System Diagram Freedom SW 3000 Owner’s GuideComprehensive Electronic Protection Protection feature This feature…Front and Side Panels Freedom SW 3000 Inverter/Charger FeaturesFront Panel Controls Status LEDs Compartment SideTwo variable-speed cooling fans are used to cool Though the transformer and power compartmentsFreedom SW AC wiring compartment access panel withAC and DC Side Panels Battery temperature sensor BTS jack providesNegative DC terminal connects to the negative AC Input 1, AC Input 2, and Inverter AC OutputSupplied Accessories Supplied AccessoriesNetwork Component Optional System Accessories and Network ComponentsAccessory Operating The Freedom SW 10 9 8 Using the SCPExit button On Start UpDown arrow button Up arrow buttonTo view the firmware revision number System Start-up Check Viewing the Firmware Revision NumberOperating Limits for Inverter Operation Operating in Invert ModeTo operate in invert mode from the front panel Charger Operation with Battery Temperature Sensor BTS Operating in Charger ModeRisk of Damage to Batteries Operating in Equalization ModeTerminating the Equalization Process Equalizing BatteriesRisk of Damage to DC Load Equipment To equalize your batteriesOperating Limits for Charger Operation Monitoring Status Messages on the SCP Monitoring the Freedom SW 3000 Indicator LightsFaults and Warnings Operating System ModesSafe To return to Operating modeTo exit Safe mode and return to Operating mode Safe ModeSystem Control Panel ConfigurationSCP System Menu Map Freedom SW 3000 Owner’s Guide System Menu MapTo view the Select Device menu Viewing the System ScreenViewing the Select Device Menu Selecting the Freedom SW 3000 Basic Menu Selecting the Freedom SW 3000 from the Select Device MenuSelecting the Freedom SW 3000 Advanced Menu To select the Freedom SW 3000 from the Select Device menuHighlighting System on the Select Device Menu To select the Freedom SW 3000 Advanced MenuReturning to Freedom SW 3000 Basic Menu Selecting the Default SettingsMenu Structure Mode DescriptionDevice Menu ModesAC Out BatteryAC Input1 Menu Basic Power ShareInverter ChargerRange of values EqualizeYes n/a Want Equalization? Screen content Explanation of items displayedRange of values Increment Default Clear FaultsBatt Type Batt SizeMenu Advanced Configure Inv/Chg Configure Inverter/ChargerView Device Info Basic MenuSub-Menus Configure Inv/Chg MenuForce Charge Cfg AC Limits Configure AC Limits# Chg Stages Eqz VoltsRisk of Damage to Equipment AC Limits Configure AC LimitsHi AC Freq View Warning Log View Fault LogView Device Info View Device Information Restore Defaults Restore DefaultsFault Types TroubleshootingFault type Behavior IntroductionTroubleshooting Section Number Troubleshooting ReferenceGeneral Troubleshooting Guidelines Troubleshooting To view a message from a warning list Number Message Type Cause SolutionTo view a fault list To view a message from a fault list Fault MessagesFault Number Message Fault Type Cause Solution AC Output Fault Number Message Fault Type Cause Solution Motor Loads Inverter ApplicationsResistive Loads Risk of Battery Damage Battery Charging ReferenceBattery Types Three-Stage charging Charge Algorithm StagesTwo-Stage Charging Flooded Charge Algorithm GraphGel Or wetFlooded Time Or wet Gel Or wet GelAGM Battery Charger Interruption Physical Specifications SpecificationsInverter Specifications Charger SpecificationsSpecifications Environmental Specifications Transfer and General SpecificationsFan Operation Regulatory ApprovalsCharger Mode Invert Power Derating vs. Ambient TemperatureWarranty Warranty and Return InformationWarranty and Return Information Product DisclaimerOut of Warranty Service Return Material Authorization PolicyReturn Procedure Information About Your System Page Page Xantrex Technology Inc