Xantrex Technology SW 3000 user service AC Output

Page 66

Troubleshooting

Table 9 Fault Messages

Fault
Number	Message	Fault Type	Cause	Solution

F6	Too many AC loads. Turn	Escalating Auto Fault.	AC Overload Shutdown	Clear the fault and attempt restart. Reduce
	some off, clear fault, try	Must occur 3 times in 30	(AC OUTPUT)	AC loads.
	again.	seconds before becoming a		Check that AC input wiring is not
		manual fault.		connected to the AC output.

F9	Battery voltage is too high.	Automatic	DC Over Voltage	Clear the fault and attempt restart. Ensure
	See guide.		Shutdown	battery voltage is 10–16 VDC at Freedom
				SW 3000 terminals. Check all other
				charging source outputs, battery cables.

F10	Battery is too low, can’t	Automatic	DC Under Voltage	Clear the fault and attempt restart.
	invert. Recharge battery.		Shutdown (Immediate)	Recharge batteries. Check battery cable
			occurs if DC voltage is	connections.
			below 8 volts DC

F11	Battery is too low, can’t	Automatic	DC Under Voltage	Clear the fault and attempt restart.
	invert. Recharge battery.		Shutdown occurs if DC	Recharge batteries. Check battery cable
			voltage is below 10 volts	connections.
			DC.

F23	Inverter/Charger internal	Escalating Auto Fault.	AC Over Voltage	Service required.
	failure. Service required.	Must occur 3 times in 30	Shutdown (Inverter AC
		seconds before becoming a	output)
		manual fault.

52	Freedom SW 3000 Owner’s Guide

Image 66

Contents Freedom SW Sine Wave Inverter/Charger Page Date and Revision About Xantrex TrademarksExclusion for Documentation Document Part NumberAbout This Guide Statement of HazardRelated Information Important Safety Instructions Electrical Shock HazardFire and Burn Hazard Explosion HazardPrecautions When Working With Batteries Exposure to Chemicals and Gases Hazard Precautions When Preparing to ChargePrecautions When Placing the Inverter/Charger Risk of Damage to the INVERTER/CHARGERRegulatory Limitations on USEContents Page Page Page Introduction Materials ListPremium Power and Ease of Use About the Freedom SW Inverter/ChargerHow the Freedom SW 3000 Inverter/Charger Works InvertingCharging Typical Xanbus System Diagram Freedom SW 3000 Owner’s Guide Xanbus SystemProtection feature This feature… Comprehensive Electronic ProtectionFront Panel Controls Status LEDs Freedom SW 3000 Inverter/Charger FeaturesFront and Side Panels Compartment SideThough the transformer and power compartments Two variable-speed cooling fans are used to coolAC wiring compartment access panel with Freedom SWNegative DC terminal connects to the negative Battery temperature sensor BTS jack providesAC and DC Side Panels AC Input 1, AC Input 2, and Inverter AC OutputSupplied Accessories Supplied AccessoriesOptional System Accessories and Network Components AccessoryNetwork Component Operating The Freedom SW Using the SCP 10 9 8Down arrow button On Start UpExit button Up arrow buttonSystem Start-up Check Viewing the Firmware Revision Number To view the firmware revision numberOperating in Invert Mode To operate in invert mode from the front panelOperating Limits for Inverter Operation Operating in Charger Mode Charger Operation with Battery Temperature Sensor BTSOperating in Equalization Mode Risk of Damage to BatteriesRisk of Damage to DC Load Equipment Equalizing BatteriesTerminating the Equalization Process To equalize your batteriesOperating Limits for Charger Operation Monitoring the Freedom SW 3000 Indicator Lights Faults and WarningsMonitoring Status Messages on the SCP System Modes OperatingTo return to Operating mode SafeSafe Mode To exit Safe mode and return to Operating modeConfiguration System Control PanelSystem Menu Map SCP System Menu Map Freedom SW 3000 Owner’s GuideViewing the System Screen Viewing the Select Device MenuTo view the Select Device menu Selecting the Freedom SW 3000 Advanced Menu Selecting the Freedom SW 3000 from the Select Device MenuSelecting the Freedom SW 3000 Basic Menu To select the Freedom SW 3000 from the Select Device menuTo select the Freedom SW 3000 Advanced Menu Highlighting System on the Select Device MenuSelecting the Default Settings Returning to Freedom SW 3000 Basic MenuDevice Menu Mode DescriptionMenu Structure ModesBattery AC Input1AC Out Inverter Power ShareMenu Basic ChargerEqualize Range of valuesYes n/a Screen content Explanation of items displayed Want Equalization?Batt Type Clear FaultsRange of values Increment Default Batt SizeView Device Info Configure Inv/Chg Configure Inverter/ChargerMenu Advanced Basic MenuConfigure Inv/Chg Menu Sub-Menus# Chg Stages Cfg AC Limits Configure AC LimitsForce Charge Eqz VoltsAC Limits Configure AC Limits Risk of Damage to EquipmentHi AC Freq View Fault Log View Device Info View Device InformationView Warning Log Restore Defaults Restore DefaultsFault type Behavior TroubleshootingFault Types IntroductionTroubleshooting Troubleshooting Reference General Troubleshooting GuidelinesSection Number Troubleshooting Number Message Type Cause Solution To view a fault listTo view a message from a warning list Fault Messages To view a message from a fault listFault Number Message Fault Type Cause Solution AC Output Fault Number Message Fault Type Cause Solution Inverter Applications Resistive LoadsMotor Loads Battery Charging Reference Battery TypesRisk of Battery Damage Charge Algorithm Stages Three-Stage chargingTwo-Stage Charging Gel Charge Algorithm GraphFlooded Or wetOr wet Gel AGMFlooded Time Or wet Gel Battery Charger Interruption Inverter Specifications SpecificationsPhysical Specifications Charger SpecificationsSpecifications Fan Operation Transfer and General SpecificationsEnvironmental Specifications Regulatory ApprovalsInvert Power Derating vs. Ambient Temperature Charger ModeWarranty and Return Information WarrantyWarranty and Return Information Disclaimer ProductReturn Material Authorization Policy Return ProcedureOut of Warranty Service Information About Your System Page Page Xantrex Technology Inc