Hitachi C 10RA2 Assembly Procedures, Assembly of Handle Bar, Installing of Rip Fence

Page 12

English

ASSEMBLY PROCEDURES

WARNING: To avoid an accident or personal injury, always confirm that the switch is turned OFF and the power plug has been disconnected from the receptacle before assembly of this tool.

1. Assembly of Handle Bar

The handle bar allows faster turning of the wheel.

When properly assembled it with rotate freely but with only a small amount of play,

(1)Tighten the screw of the handle bar until it hits against the wheel.

(2)Securely tighten the handle bar nut with a wrench.

Wheel

Handle Bar

Fig. 6

2. Installing of Rip Fence

CAUTION: The rip fence must be aligned parallel to the saw blade to minimize the kickback (refer to page 19).

Grip

Support

Rear Rail

Front Rail

The rip fence can be conveniently used to cut a workpiece into different pieces of precise width or into parallel pieces. It can be mounted on either the right or left side of the table.

(1)

Tighten the screw of the grip.

(2)

Catch the hook of the support in the bottom part of the rear

 

rail.

(3)

Lower the rip fence in the arrow direction, and fit the part of

 

the width body and support to the groove of the front and

 

rear rail.

Width Body

Fig. 7

(4) Confirm that the rip fence is moved right and left and it moves

smoothly.

3. Assembly of Miter Gauge

Miter Gauge Groove

Sheet Bar

Miter Gauge

The miter gauge is convenient for cutting long or angular pieces which are difficult to work on with the rip fence. It can be mounted on either the right or left side of the table. Align the sheet bar of miter gauge with the miter gauge groove and slide it in the direction indicated by the arrow through the front of the table.

Fig. 8

12

Image 12
Contents Avertissement AdvertenciaContents Meanings of Signal Words Important Safety Instructions for Using ALL Power ToolsImportant Information Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordGrounding Instructions Fig. aOperation and Maintenance Name of PartsSpecifications AccessoriesApplications UnpackingInstallation Preparation Before OperationAssembly Procedures Assembly of Handle BarInstalling of Rip Fence Assembly of Miter GaugeMounting and adjusting Saw Blade Guard Assembly Mounting Table InsertAdjustment Assembly of Table Saw Stand Optional AccessoryAdjustment of saw blade parallel to miter gauge groove Adjusting 90 and 45 positive stops Adjustment of rip fence Before Using Adjustment of pointerAdjustment of Miter Gauge Practical Applications Raising and lowering saw blade Saw Blade Tilting OperationRip Fence Operation Operating Instructions Miter Gauge OperationRipping Bevel RippingRipping small pieces Cross CuttingMitering Compound Mitering Work HelpersDado Cutting Mounting the dado blade setMaintenance and Inspection SAW Blade Mounting and DismountingMounting the saw blade Dismounting the saw bladeFrequently clean the saw blade guard CleaningInspecting the carbon brushes and Fig Inspecting the mounting screwsService and Repairs Informations Importantes Signification DES Mots D’AVERTISSEMENTConsignes DE Sécurité Relatives AUX Outils Électriques Consignes de sécurité spéciales pour cet outil électrique Français Français Pieces DE Rechange Utilisation DUN Cordon DE RallongeInstructions DE Mise À LA Masse Méthodes DE Mise À LA MasseUtilisation ET Entretien NOM DES PiècesAccessoires SpécificationsAccessoires EN OPTION…vendus séparément DéballagePréparation Avant L’UTILISATION Méthodes DE Montage Montage de la manivellePose du guide pour coupe de fil Montage du guide pour coupe d’ongletMontage de l’insert de table Assemblage du support de scie de table Accessoire en option RéglageRéglage des butées positives à 90 et Réglage du guide pour coupe de fil Avant L’UTILISATION Réglage du repèreRéglage du guide pour coupe d’onglet Vérifier que l’interrupteur est sur OFFApplication Dispositif de protection contre les surcharges du moteur Soulèvement et abaissement de la lame de scieInclinaison de la lame de scie Utilisation du guide pour coupe de filAvertissements DE Fonctionnement Utilisation du guide de coupe d’ongletInstructions D’UTILISATION Coupe de filCoupe de fil en biseau Coupe de fil de petites piècesCoupe de mise à longueur Coupe de mise à longueur en biseauCoupe d’onglet composée Aides au travailRainurage Montage de l’ensemble de lame à rainurerInstallation ET Retrait DE LA Lame Installation de la lameEntretien ET Inspection Retrait de la lameInspecter les balais carbone et Fig Inspection des vis de montageNettoyer fréquemment la protection de lame de scie RemisageService APRÈS-VENTE ET Réparations Información Importante Significado DE LAS Palabras ClaveNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilización DE UN Cable ProlongadorAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Metodos DE Puesta a TierraOperación Y Mantenimiento Nomenclatura DE PartesEspecificaciones AccesoriosAplicaciones DesembalajePreparativos Previos a LA Operación InstalaciónProcedimientos DE Armado Armado del mango de la ruedaInstalación del tope-guía Armado de la guía de ingletesMontaje del inserto de mesa Ajuste Armado del soporte de la sierra de mesa accesorio opcionalAjuste de los topes de seguridad a 90 y Ajuste del tope-guía Ajuste del indicador Ajuste de la guía de ingletesAntes DE LA Utilización Aplicaciones PrácticasDispositivo de protección contra la sobrecarga del motor Elevación y descenso de la hoja de sierraOperación de inclinación de la hoja de sierra Advertencias Sobre EL Funcionamiento Operación del tope-guíaOperación de la guía de ingletes Instrucciones DE Funcionamiento Aserrado al hiloCorte al hilo en bisel Corte al hilo de piezas pequeñasCorte transversal Corte de ingletes Corte de ingletes compuestoPiezas auxiliares Corte de ranurar Montaje del juego de hojas de ranurar Montaje Y Desmontaje DE LA Hoja DE Sierra Mantenimiento E InspecciónMontaje de la hoja de sierra Desmontaje de la hoja de sierraInspeccion las de escobillas Figs y Inspección de los tornillos de montajeInspección del funcionamiento del protector de la hoja Limpie frecuentemente el protector de la hoja de sierraServicio Y Reparaciones LimpiezaParts List Model C10RA2 Table Saw Parts List Motor Parts List Hitachi Koki Canada Co