Hitachi C 10RA2 instruction manual Adjustment, Assembly of Table Saw Stand Optional Accessory

Page 14

English

6.Mounting Elbow (Chip Extraction Duct) (Standard Accessory)

Connect a 2 – 9/16" (65 mm) hose of dust collector to the chip extraction duct to suck cutting chips away. Mount the chip extraction duct on the chip discharge outlet at the body rear of the body.

Elbow (Chip Extraction Duct)

Fig. 11

7. Assembly of Table Saw Stand (Optional Accessory)

Leg

Stay

Washer

Cap Square Neck Bolt

Nut

Rubber Cap

Fig. 12-a

Fig. 12-b

Fig. 12-c

Assemble it with the stay and leg(s). Set the stays below and assemble the legs outside (see Fig. 12-c).

Secure with cup square neck bolts and nuts (see Fig. 12-a).

Then attach rubber caps underneath the legs (see Fig. 12-b).

ADJUSTMENT

This tool is accurately adjusted before shipping from the factory.

Check the following accuracies and readjust them if necessary in order to obtain the best results in operation.

WARNING: To avoid an accident or personal injury, always confirm that the switch is turned off and the power plug has been disconnected from the receptacle before adjustment of this tool.

1. Adjustment of saw blade parallel to miter gauge groove.

This is the most probably difficult of the adjustments. Before shipment from the factory this adjustment was made but it should be rechecked and readjusted if necessary.

CAUTION: This adjustment must be correct. Kickback could result and accurate cuts cannot be made.

Saw Blade

Down

Up

Loosen

 

Wheel

Tighten

Tilt Lock Handle

 

Fig. 13-a

(1)Loosen the saw blade tilt lock handle by turning it counterclockwise. Move the saw blade tilting mechanism to the left and set the saw blade to 0° with the stopper.

(2)Turn the wheel fully clockwise and set the saw blade to the maximum cutting height (see Fig. 13-a).

(3)Select a tooth on the saw blade which is bent to the right.

(4)Mark that tooth with a pencil or permanent marker.

(5)Set the miter gauge to 90° and tighten the clamp handle (B) to lock it in that position. Place the miter gauge in the left hand miter gauge groove in the table top (see Fig. 13-b).

14

Image 14
Contents Avertissement AdvertenciaContents Important Information Meanings of Signal WordsImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension CordGrounding Instructions Fig. aOperation and Maintenance Name of PartsSpecifications AccessoriesApplications UnpackingInstallation Preparation Before OperationInstalling of Rip Fence Assembly ProceduresAssembly of Handle Bar Assembly of Miter GaugeMounting and adjusting Saw Blade Guard Assembly Mounting Table InsertAdjustment of saw blade parallel to miter gauge groove AdjustmentAssembly of Table Saw Stand Optional Accessory Adjusting 90 and 45 positive stops Adjustment of rip fence Adjustment of Miter Gauge Before UsingAdjustment of pointer Practical Applications Rip Fence Operation Raising and lowering saw bladeSaw Blade Tilting Operation Operating Instructions Miter Gauge OperationRipping Bevel RippingMitering Ripping small piecesCross Cutting Compound Mitering Work HelpersDado Cutting Mounting the dado blade setMounting the saw blade Maintenance and InspectionSAW Blade Mounting and Dismounting Dismounting the saw bladeInspecting the carbon brushes and Fig Frequently clean the saw blade guardCleaning Inspecting the mounting screwsService and Repairs Consignes DE Sécurité Relatives AUX Outils Électriques Informations ImportantesSignification DES Mots D’AVERTISSEMENT Consignes de sécurité spéciales pour cet outil électrique Français Français Pieces DE Rechange Utilisation DUN Cordon DE RallongeInstructions DE Mise À LA Masse Méthodes DE Mise À LA MasseUtilisation ET Entretien NOM DES PiècesAccessoires SpécificationsAccessoires EN OPTION…vendus séparément DéballagePréparation Avant L’UTILISATION Pose du guide pour coupe de fil Méthodes DE MontageMontage de la manivelle Montage du guide pour coupe d’ongletMontage de l’insert de table Assemblage du support de scie de table Accessoire en option RéglageRéglage des butées positives à 90 et Réglage du guide pour coupe de fil Réglage du guide pour coupe d’onglet Avant L’UTILISATIONRéglage du repère Vérifier que l’interrupteur est sur OFFApplication Inclinaison de la lame de scie Dispositif de protection contre les surcharges du moteurSoulèvement et abaissement de la lame de scie Utilisation du guide pour coupe de filAvertissements DE Fonctionnement Utilisation du guide de coupe d’ongletInstructions D’UTILISATION Coupe de filCoupe de mise à longueur Coupe de fil en biseauCoupe de fil de petites pièces Coupe de mise à longueur en biseauCoupe d’onglet composée Aides au travailRainurage Montage de l’ensemble de lame à rainurerEntretien ET Inspection Installation ET Retrait DE LA LameInstallation de la lame Retrait de la lameNettoyer fréquemment la protection de lame de scie Inspecter les balais carbone et FigInspection des vis de montage RemisageService APRÈS-VENTE ET Réparations Normas DE Seguridad Para LAS Herramientas Eléctricas Información ImportanteSignificado DE LAS Palabras Clave Español Español Español Piezas DE Reemplazo Utilización DE UN Cable ProlongadorAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Metodos DE Puesta a TierraOperación Y Mantenimiento Nomenclatura DE PartesEspecificaciones AccesoriosAplicaciones DesembalajePreparativos Previos a LA Operación InstalaciónInstalación del tope-guía Procedimientos DE ArmadoArmado del mango de la rueda Armado de la guía de ingletesMontaje del inserto de mesa Ajuste Armado del soporte de la sierra de mesa accesorio opcionalAjuste de los topes de seguridad a 90 y Ajuste del tope-guía Ajuste del indicador Ajuste de la guía de ingletesAntes DE LA Utilización Aplicaciones PrácticasOperación de inclinación de la hoja de sierra Dispositivo de protección contra la sobrecarga del motorElevación y descenso de la hoja de sierra Operación de la guía de ingletes Advertencias Sobre EL FuncionamientoOperación del tope-guía Instrucciones DE Funcionamiento Aserrado al hiloCorte transversal Corte al hilo en biselCorte al hilo de piezas pequeñas Piezas auxiliares Corte de ingletesCorte de ingletes compuesto Corte de ranurar Montaje del juego de hojas de ranurar Montaje de la hoja de sierra Montaje Y Desmontaje DE LA Hoja DE SierraMantenimiento E Inspección Desmontaje de la hoja de sierraInspección del funcionamiento del protector de la hoja Inspeccion las de escobillas Figs yInspección de los tornillos de montaje Limpie frecuentemente el protector de la hoja de sierraServicio Y Reparaciones LimpiezaParts List Model C10RA2 Table Saw Parts List Motor Parts List Hitachi Koki Canada Co