Outback Power Systems MX60 user manual OutBack Power Systems Inc

Page 11

NOTES

•An optional battery Remote Temperature Sensor (RTS) is recommended for accurate battery recharging (only one RTS is needed for multiple OutBack Series Inverter/Chargers and MX60 units when an OutBack HUB and a MATE are parts of the system). When one RTS is used, it must be connected to the component plugged into the Port 1 of the HUB.

•AUX modes include powering a relay, LED indicator, and Piezo-buzzer or brushless fan.

•The OutBack MATE can display a single MX60 or multiple MX60s if connected to a HUB.

•Surge protection on the input (PV) side of the MX60 and on the battery side is required for extended warranty protection. A dwelling rooftop array requires ground fault protection (OutBack OBDC-GFP/2 recommended).

•Always install the MX60 in an upright position. The MX60 must be secured for a safe installation and to retain warranty protection. Use a 1 5/8” wood screw through the slotted hole at the top of the MX60 and at least two screws in the internally located holes at the bottom of the MX60’s enclosure.

OutBack Power Systems Inc.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents MX60 PV Mppt Dear OutBack Customer Warranty SummaryJanuary 29, 2007 REV 7.0 Software REV 5.10 EN 61000-6-3 seeTable of Contents Battery Temperature Compensated Voltage SET Point Introduction MX60 PV Mppt Maximum Power Point Tracking Charge ControllerScope OutBack Power Systems Inc Personal Precautions To 0 C 49 to 32 F Open Circuit VOLTAGE/WIRE and Disconnect SizingWire and Disconnect Sizing Check the PV array voltage before connecting it to the MX60Field Wiring Connections and Surge Protection OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc KEY to the Example Diagrams Battery System VoltageOFF Screen this screen is initially blank at power up Powering UPEnter + PasswordExitenter 150Are you sure? 12 24 36 48 NOYes OutBack12V Power Systems MX60Battery Voltage Screen Exit EnterWatts Aux Off Status ScreenPV 005 Bat 12.5 00.0 aMppt PV 113 Bat 12.5 00.0 a Watts 0000 Aux Off KWHrs SleepingPV 087 Bat 12.5 05.0 a 32.9 a Watts 0412 Aux Off KWHrs 00.0 Exit Accessing the Main MenuCharger Aux Light Misc Logging60.0 14.4 13.6 Charger SetupLimit Absorb Amps VoltsOff AUX ModeTerminals. OFF indicates changes to the next mode VDC ManualAUX Mode Path OutBack Power Systems Inc Vent FAN Volts AUX ModeExit Next on OFF AUX Mode Exit Next140 Back + PV Trigger OffExit Next Time Volt PV Volts Hold Time Sec 01.1 Back + Exit Next Time Volt AUX ModePV Trigger Exit Next Time VoltBack AUX Mode Error Alarm Exit NextDiversion Off Absorb-Float-EQ Relative Volts 00.0 00.2Example of Diversion Hold Delay 01.0 Time SecondsDiversion Load and AUX Wiring Set-Up Illustrated 001 TimerLow Batt Disconnect Sec14.4 Back + DisV Exit Next Time Volt Disconnect Volts+ ReCon RE-CONNECT VoltsPress the Next soft key to view the Remote screen Remote OffLogging Log2 Charger Aux *Light EQ Misc Optimize Logging Log2 EQ-BATTERY EqualizeBacklight Backlight Control Always Exit Auto on OFFBack Auto Start Stop Battery EqualizeExit NEX -EQV +EQV Battery Equalize Exit Next -HRS +HRSExit DAY +DAY Auto ModeCount 000Exit Next Wide Rstrt MISC-MISCELLANEOUSGT State PWM% ChgT 255 07 50.0 005 Tmp Comp a14.4 f13.6 WIDE/LMIT Battery Temperature Compensated Limits 14.8 Back + DisV 13.2 Lower LimitDisV 14.8Force Float = fl oat cycle Force Bulk = bulk cycle Exit Next Wide Rstrt Force Exit Next Float BulkAMP +AMP Miscellaneous ScreenPCB CFBExit Advanced Menu Snooze Mode LowcutoffAdvanced Charger Aux Light Misc *Advanced Logging Log2Mpp Range Limit %Voc min max Exit Next 1/2 90% Park Mpp 77 % Voc Exit Next -Voc +VocExit Next -V +V Sweep Interval MinutesExit Next -MIN MAX+ Advanced Menu Vbatt Calibration 12.8vThis screen allows the user to choose one of these modes Mppt Mode Auto Sweep Exit Next nonGT ModeLow Cutoff Amp Exit Next MIN+ MAX+ Absorb Time Limits 000m 2hrExit Clear Back Totl Daly Data LoggingDaily KWhours 00.0 Float time mins 0000 TotalKWh 0000 Exit CLR +DAY -DAYPressing Back brings back the Logging screen Charger Aux Light Misc Advanced Logging Log2Clearing Totals and Daily Stats PkBatV Voc HiVoc 012.2 070.2 076.9 Daily peak Battery voltageOperational mode LOG2Auto Restart PkBatV Voc HiVoc 012.2 070.2 Mppt Sunrise Exit NextThis value is the peak daily Watts seen by the MX60 0000 float Tmin HighWatts Lo 13.2 Hi DCkWhSecondary LOG2 Screen MICRO-HYDRO and Fuel Cell Systems Performance Optimization MICRO-HYDRO, Wind TURBINE, and Fuel Cell ApplicationsOutBack Power Systems Inc Advanced Menu Micro-Hydro Advanced Menu Park Mpp 77 % VOC Exit Next -Voc +Voc PV 087 Bat 12.0 05.0 a 35.8A Watts This page Intentionally Left Blank Application Notes Calling the Factory for Assistance Voltage step down capability SpecificationsWarranty Dimensions Weight Amps Volts 60.0 14.4 13.6 Limit Absorb Float60.00 24V and 48V Battery System Efficiency Curve MX60 Efficiency vs. Input Power GraphUnderstanding the Various Operational Modes OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc MATE-DISPLAYED MX60 Status Mode Screens MATE-DISPLAYED MX60 Status Meter Screens MATE-DISPLAYED MX60 Status Setpt Setpoint Screens Troubleshooting Guide OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc Typical Array Sizing Guide Standard version Standard vs. Australian Default Settings% Voltage Drop 12, 24 or 48 Volt Battery System Volt PV Array 80V MPP Typical Wire and Disconnect Sizing MX60 MULTI-STAGE Battery Charging OutBack Power Systems Inc Average = 86˚ F / 30˚ C Battery Temperature Compensated Volatge SET PointAverage = 95˚ F / 35˚ C Suggested Battery Charger SET Points TWO Year Limited Warranty Information OutBack Power Systems Inc EU Declaration of Conformity OWNER’S System Information Products Covered Serial Number Product RegistrationInverter/Chargers REV B

MX60 specifications

The Outback Power Systems MX60 is a state-of-the-art solar charge controller designed for off-grid and grid-tied systems, providing users with cutting-edge technology and efficiency in managing their solar energy resources. This device stands out in the renewable energy market due to its versatile features, robust performance, and ease of use.

One of the main features of the MX60 is its high-efficiency MPPT (Maximum Power Point Tracking) technology. This advanced technology optimizes the energy harvested from solar panels by adjusting the electrical operating point of the modules, allowing the system to extract the maximum available power. The MX60 can handle a considerable input voltage of up to 150 volts and offers a maximum output current of 60 amps, making it suitable for both small and large-scale installations.

The MX60’s robust architecture ensures its durability in harsh environmental conditions. With an operating temperature range of -40°F to 176°F, the charge controller performs reliably in varied climatic conditions, whether in extreme heat or bitter cold. This makes it an ideal choice for remote locations and rugged terrains where traditional power sources might be unreliable or unavailable.

An intuitive LCD interface equipped with a user-friendly display allows for easy monitoring and configuration. Users can track real-time performance metrics, including solar array voltage, output current, battery voltage, and charging status. The device is also equipped with advanced programmable settings, offering users complete control over charging parameters and battery maintenance.

Moreover, the MX60 incorporates essential safety features, including over-voltage and over-current protection, reverse polarity protection, and temperature compensation. Such safety measures are crucial in preventing damages to both the controller and the connected battery system.

The MX60 is compatible with various battery types, including Flooded, AGM, Gel, and Lithium, providing flexibility in energy storage options. It seamlessly integrates with Outback's Radian inverter systems, facilitating a comprehensive energy management solution for residential and commercial applications.

In summary, the Outback Power Systems MX60 is an exceptional choice for those looking for a reliable and efficient solar charge controller. Its combination of advanced technology, robust construction, and user-friendly features makes it an essential component for anyone interested in harnessing the power of solar energy.
Top Page Image Contents