Outback Power Systems MX60 user manual WIDE/LMIT Battery Temperature Compensated Limits

Page 38

WIDE/LMIT Battery Temperature Compensated Limits

During cold weather, a battery often requires a higher recharging voltage. Lower quality inverters might not accommodate these higher voltages and can shut down during recharging, cutting off power to their loads. The MX60 allows the user to lower the compensated voltage in the Absorb cycle so these inverters will remain operating. Also, some batteries have an absolute voltage limit that should not be exceeded and the WIDE/LMIT option allows the user to control this during re- charging. WIDE allows the RTS full control over recharging; LMIT sets the ceiling and fl oor voltages for the RTS.

During hot weather, the LMIT feature set point assures recharging will continue at a high enough voltage rather than dropping too low in reaction to a higher ambient temperature. This assures the recharging voltage adequately charges, but should be monitored according to the battery manufacturer’s recommendations.

The RTS default compensated voltages apply if the WIDE/LMIT option is set to WIDE in the MISC menu. The upper and lower LMIT settings can be viewed in the second menu of the Log2 screen when LMIT is selected.

The LMIT set points can be set in the AUX MODE menu. To set the LMIT upper and lower set points, press the #1 soft key once and return to the MAIN Menu. From the MAIN Menu, access the AUX MODE screens and then the Low Batt Disconnect screen.

Path for Setting the LMIT Upper and Lower Set Points using AUX:

*Charger

Aux

Light

Charger

*Aux

Light

EQ

Misc

Advance

EQ

Misc

Advance

Logging

 

Log2

Logging

 

Log2

EXIT

 

GO

EXIT

 

GO

AUX MODE

DISCONNECT VOLTS

Low Batt Disconnect

 

 

<13.6

 

On

 

 

 

 

EXIT NEXT TIME VOLT

BACK

-

+

ReCon

Press <NEXT> until Low Batt Disconnect appears, then press <VOLT>

38

OutBack Power Systems Inc.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents MX60 PV Mppt Warranty Summary Dear OutBack CustomerEN 61000-6-3 see January 29, 2007 REV 7.0 Software REV 5.10Table of Contents Battery Temperature Compensated Voltage SET Point Introduction MX60 PV Mppt Maximum Power Point Tracking Charge ControllerScope OutBack Power Systems Inc Personal Precautions Check the PV array voltage before connecting it to the MX60 Open Circuit VOLTAGE/WIRE and Disconnect SizingWire and Disconnect Sizing To 0 C 49 to 32 FField Wiring Connections and Surge Protection OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc Battery System Voltage KEY to the Example DiagramsPowering UP OFF Screen this screen is initially blank at power up150 PasswordExitenter Enter +Exit Enter OutBack12V Power Systems MX60Battery Voltage Screen Are you sure? 12 24 36 48 NOYes00.0 a Status ScreenPV 005 Bat 12.5 Watts Aux OffMppt PV 113 Bat 12.5 00.0 a Watts 0000 Aux Off KWHrs SleepingPV 087 Bat 12.5 05.0 a 32.9 a Watts 0412 Aux Off KWHrs 00.0 Logging Accessing the Main MenuCharger Aux Light Misc ExitAmps Volts Charger SetupLimit Absorb 60.0 14.4 13.6Manual AUX ModeTerminals. OFF indicates changes to the next mode VDC OffAUX Mode Path OutBack Power Systems Inc Exit Next AUX ModeExit Next on OFF AUX Mode Vent FAN Volts140 Back + PV Trigger OffExit Next Time Volt PV Volts Exit Next Time Volt Exit Next Time Volt AUX ModePV Trigger Hold Time Sec 01.1 Back +Absorb-Float-EQ Relative Volts 00.0 00.2 AUX Mode Error Alarm Exit NextDiversion Off BackHold Delay 01.0 Time Seconds Example of DiversionDiversion Load and AUX Wiring Set-Up Illustrated Sec TimerLow Batt Disconnect 001RE-CONNECT Volts Exit Next Time Volt Disconnect Volts+ ReCon 14.4 Back + DisVPress the Next soft key to view the Remote screen Remote OffLogging Log2 Backlight Control Always Exit Auto on OFF EQ-BATTERY EqualizeBacklight Charger Aux *Light EQ Misc Optimize Logging Log2Exit Next -HRS +HRS Battery EqualizeExit NEX -EQV +EQV Battery Equalize Back Auto Start Stop000 Auto ModeCount Exit DAY +DAYExit Next Wide Rstrt MISC-MISCELLANEOUSGT State PWM% ChgT 255 07 50.0 005 Tmp Comp a14.4 f13.6 WIDE/LMIT Battery Temperature Compensated Limits 13.2 Lower Limit 14.8 Back + DisV14.8 DisVExit Next Wide Rstrt Force Exit Next Float Bulk Force Float = fl oat cycle Force Bulk = bulk cycleCFB Miscellaneous ScreenPCB AMP +AMPCharger Aux Light Misc *Advanced Logging Log2 Snooze Mode LowcutoffAdvanced Exit Advanced MenuPark Mpp 77 % Voc Exit Next -Voc +Voc Mpp Range Limit %Voc min max Exit Next 1/2 90%Vbatt Calibration 12.8v Sweep Interval MinutesExit Next -MIN MAX+ Advanced Menu Exit Next -V +VThis screen allows the user to choose one of these modes Mppt Mode Auto Sweep Exit Next nonGT ModeLow Cutoff Amp Absorb Time Limits 000m 2hr Exit Next MIN+ MAX+Exit Exit CLR +DAY -DAY Data LoggingDaily KWhours 00.0 Float time mins 0000 TotalKWh 0000 Clear Back Totl DalyPressing Back brings back the Logging screen Charger Aux Light Misc Advanced Logging Log2Clearing Totals and Daily Stats LOG2 Daily peak Battery voltageOperational mode PkBatV Voc HiVoc 012.2 070.2 076.9PkBatV Voc HiVoc 012.2 070.2 Mppt Sunrise Exit Next Auto RestartThis value is the peak daily Watts seen by the MX60 0000 float Tmin HighWatts Lo 13.2 Hi DCkWhSecondary LOG2 Screen MICRO-HYDRO, Wind TURBINE, and Fuel Cell Applications MICRO-HYDRO and Fuel Cell Systems Performance OptimizationOutBack Power Systems Inc Advanced Menu Micro-Hydro Advanced Menu Park Mpp 77 % VOC Exit Next -Voc +Voc PV 087 Bat 12.0 05.0 a 35.8A Watts This page Intentionally Left Blank Application Notes Calling the Factory for Assistance Voltage step down capability SpecificationsWarranty Dimensions Weight Limit Absorb Float Amps Volts 60.0 14.4 13.660.00 MX60 Efficiency vs. Input Power Graph 24V and 48V Battery System Efficiency CurveUnderstanding the Various Operational Modes OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc MATE-DISPLAYED MX60 Status Mode Screens MATE-DISPLAYED MX60 Status Meter Screens MATE-DISPLAYED MX60 Status Setpt Setpoint Screens Troubleshooting Guide OutBack Power Systems Inc OutBack Power Systems Inc OutBack Power Systems Inc Typical Array Sizing Guide Standard vs. Australian Default Settings Standard version% Voltage Drop 12, 24 or 48 Volt Battery System Volt PV Array 80V MPP Typical Wire and Disconnect Sizing MX60 MULTI-STAGE Battery Charging OutBack Power Systems Inc Average = 86˚ F / 30˚ C Battery Temperature Compensated Volatge SET PointAverage = 95˚ F / 35˚ C Suggested Battery Charger SET Points TWO Year Limited Warranty Information OutBack Power Systems Inc EU Declaration of Conformity OWNER’S System Information Products Covered Serial Number Product RegistrationInverter/Chargers REV B

MX60 specifications

The Outback Power Systems MX60 is a state-of-the-art solar charge controller designed for off-grid and grid-tied systems, providing users with cutting-edge technology and efficiency in managing their solar energy resources. This device stands out in the renewable energy market due to its versatile features, robust performance, and ease of use.

One of the main features of the MX60 is its high-efficiency MPPT (Maximum Power Point Tracking) technology. This advanced technology optimizes the energy harvested from solar panels by adjusting the electrical operating point of the modules, allowing the system to extract the maximum available power. The MX60 can handle a considerable input voltage of up to 150 volts and offers a maximum output current of 60 amps, making it suitable for both small and large-scale installations.

The MX60’s robust architecture ensures its durability in harsh environmental conditions. With an operating temperature range of -40°F to 176°F, the charge controller performs reliably in varied climatic conditions, whether in extreme heat or bitter cold. This makes it an ideal choice for remote locations and rugged terrains where traditional power sources might be unreliable or unavailable.

An intuitive LCD interface equipped with a user-friendly display allows for easy monitoring and configuration. Users can track real-time performance metrics, including solar array voltage, output current, battery voltage, and charging status. The device is also equipped with advanced programmable settings, offering users complete control over charging parameters and battery maintenance.

Moreover, the MX60 incorporates essential safety features, including over-voltage and over-current protection, reverse polarity protection, and temperature compensation. Such safety measures are crucial in preventing damages to both the controller and the connected battery system.

The MX60 is compatible with various battery types, including Flooded, AGM, Gel, and Lithium, providing flexibility in energy storage options. It seamlessly integrates with Outback's Radian inverter systems, facilitating a comprehensive energy management solution for residential and commercial applications.

In summary, the Outback Power Systems MX60 is an exceptional choice for those looking for a reliable and efficient solar charge controller. Its combination of advanced technology, robust construction, and user-friendly features makes it an essential component for anyone interested in harnessing the power of solar energy.
Top Page Image Contents