Porter-Cable 90550107, PCL180ID Operating Instructions, Variable Speed Trigger Switch FIG. E

Page 10

90550107 PC1800ID, PC1200ID 4/1/09 9:33 AM Page 10

OPERATING INSTRUCTIONS

VARIABLE SPEED TRIGGER SWITCH (FIG. E)

To turn the tool on, squeeze the trigger switch (1). E To turn the tool off, release the trigger switch. Your tool is equipped with a brake. The chuck will stop

as soon as the trigger switch is fully released. The variable speed switch enables you to select the best speed for a particular application. The more you squeeze the trigger, the faster the tool will operate. Use lower speeds for starting holes without a center punch, drilling in metals or plastics, or driving screws. For maximum tool life, use variable speed only for starting holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided.

FORWARD/REVERSE CONTROL BUTTON

F

(FIG. F)

A forward/reverse control button (2) determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool. To select reverse, depress the forward/reverse control button on the left side of the tool. The center position of the control button locks the tool in the OFF position. When changing the position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing

the direction of rotation, you may hear a click on start up. This and the impacting noise that the tool makes is normal and does not indicate a problem.

LED WORKLIGHT (FIG. G)

There is a worklight (5) located just above the trigger switch (A). The worklight will be activated when the trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate work surface and is not intended to be used as a flashlight.

QUICK RELEASE CHUCK (FIG. H)

NOTE: The chuck accepts 1/4 inch (6.35 mm) hex accessories only.

Place the switch in the locked off (center) position or remove battery pack before changing accessories.

To install an accessory, pull the chuck collar (3) away from the front of the tool, insert the accessory, and release the collar. The accessory is locked in place.

To remove an accessory, pull the chuck collar (3) away from the front of the tool, remove the accessory and release the collar.

G

H

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Advertencia Léase Este Catalog Numbers PCL180IDGeneral Power Tool Safety Warnings Specific Safety Rules Safety Guidelines Definitions Symbols Important Safety Instructions for Battery Chargers Battery CAP Information Storage RecommendationsBAD Battery Charging ProcedureCharger Diagnostics HOT/COLD Pack DelayInstalling and Removing the Battery Pack from the Tool FORWARD/REVERSE Control Button Variable Speed Trigger Switch FIG. EOperating Instructions LED Worklight FIG. GOn Board BIT Storage TroubleshootingMaintenance Specialnotes for USE with Lithium BatteriesReplacement Parts Service and Repairs Three Year Limited WarrantyAccessories Highway North Jackson, TN 888 DE Catalogue PCL180ID 90550107 PC1800ID, PC1200ID 4/1/09 933 AM 90550107 PC1800ID, PC1200ID 4/1/09 933 AM Consignes DE Sécurité Particulières Symboles Lignes Directrices EN Matière DE Sécurité DéfinitionsDescription Fonctionnelle Figure aLire Toutes LES Directives Information Concernant LE Capuchon DU BLOC-PILE Recommandations EN Matière DE RangementProcédure DE Charge Fonction DE Suspension DU BLOC-PILES CHAUD/FROID Fonctions DE Diagnostic DU ChargeurPile EN Mauvais État Problème Avec LE SecteurInsertion ET Retrait DU BLOC-PILES DE L’OUTIL Bouton DE Commande Marche AVANT/MARCHE Arrière FIG. FFonctionnement Détente À Vitesse Variable FIG. EMandrin À Blocage Rapide FIG. H LE Sceau SrprcmcLampe DE Travail À DEL FIG. G EntretienRemarques Spéciales SUR L’EMPLOIAVEC DES Pilesau Lithium AccessoiresDépannage Entretien ET RéparationRemplacement DES Étiquettes D’AVERTISSEMENT Garantie Limitée DE Trois ANSCatálogo N PCL180ID 90550107 PC1800ID, PC1200ID 4/1/09 933 AM 90550107 PC1800ID, PC1200ID 4/1/09 933 AM Normas Específicas DE Seguridad Pautas DE SEGURIDAD/DEFINICIONES SímbolosDescripción DE LAS Funciones Figura a LEA Todas LAS Instrucciones Recomendaciones CON Respecto AL Almacenamiento Información Acerca DEL Protector DE LA BateríaProcedimiento DE Carga Batería EN MAL Estado Línea DE Potencia CON ProblemasDiagnóstico DEL Cargador Retraso POR Paquete CALIENTE/FRÍOInstrucciones DE Operación Interruptor Disparador DE Velocidad Variable Figura ELUZ DE Trabajo DE LED Figura G Botón DE Control DE AVANCE/REVERSAPortabrocas DE Liberación Rápida Figura H Notas Especiales Paraeluso CON Baterías DE Litio Detección DE ProblemasEL Sello Rbrc MantenimientoPiezas DE Repuesto Mantenimiento Y Reparaciones Garantía Limitada DE Tres AñosAccesorios Pcmvc Pclmvc Pcxmvc Reemplazo DE LAS Etiquetas DE Advertencia
Top Page Image Contents