Porter-Cable PC700D, PC650HD Volts Amperes Hertz Watts, Double insulated Per minute

Page 4

90538205 PC700D & PC650HD 7/2/08 12:28 PM Page 4

with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

Symbols

•The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V

volts

A

amperes

Hz

hertz

W

watts

min

minutes

no

alternating current

direct current

no load speed

Class I Construction

earthing terminal

................

..................

(grounded)

................

safety alert symbol

................

Class II Construction

.../min or rpm

revolutions or reciprocation

(double insulated)

per minute

4

Image 4

Contents PRODUCTO.CATALOG Numbers PC650HD Advertencia Léase EstePC700D General Safety Rules Work area safetySpecific Safety Rules Volts Amperes Hertz Watts Double insulated Per minuteFunctional Description Figure a & B Safety Warnings and Instructions Drills Assembly Operating InstructionsSelecting the Drilling Mode PC650HD Figure G Setting the Drilling Depth PC650HD Figure DSwitching on and OFF TWO-GEAR Selector PC650HD Figure HTroubleshooting Three Year Limited Warranty Manuel dinstructions DE Catalogue90538205 PC700D & PC650HD 7/2/08 1229 PM 90538205 PC700D & PC650HD 7/2/08 1229 PM Consignes DE Sécurité Particulières Symboles Lignes Directrices EN Matière DE Sécurité DéfinitionsVolts Ampères Hertz Watts SécuritéInsérer UNE Mèche OU UN Autre Accessoire FIG. E AssemblageAvertissements DE Sécurité ET Directives Perceuses Fixation DE LA Poignée Latérale FIG. DFonctionnement Perçage DU Bois Mode PerçagePerçage DU Métal Problème Cause possible Solution possible DépannageEntretien Pièces DE Rechange Entretien ET RéparationRemplacement DES Étiquettes D’AVERTISSEMENT AccessoiresGarantie Limitée DE Trois ANS Highway 45 North Jackson, Tennessee 888 Manual deinstrucciones Catálogo NPC650D PC700HD90538205 PC700D & PC650HD 7/2/08 1229 PM 90538205 PC700D & PC650HD 7/2/08 1229 PM Normas DE Seguridad Específicas Pautas DE SEGURIDAD/DEFINICIONESDescripción DE LAS Funciones Figura a y B SímbolosInstrucciones Y Advertencias DE Seguridad Taladros Ensamblaje Instrucciones DE OperaciónAcoplamiento DEL Mango Lateral FIG. D Inserción DE UNA Broca U Otro Accesorio Figura ESelección DE LA Dirección DE Rotación Selección DEL Modo DE Taladrado PC650HD FIG. GSelector DE DOS Engranajes PC650HD FIG. H Ajuste DE LA Profundidad DE Perforación PC650HD FIG. DTaladrado EN Madera TaladradoTaladrado EN Metal Detección DE Problemas Problema Causa posible Solución posibleMantenimiento Piezas DE Repuesto Mantenimiento Y ReparacionesAccesorios Garantía Limitada DE Tres AñosReemplazo DE LAS Etiquetas DE Advertencia Especificaciones PC700PC650 Catalog Numbers PC650HD, PC700D Form # July ‘08