Grizzly G1010 Stand Assembly, Components and Hardware Needed Qty, To assemble the stand

Page 18

Stand Assembly

Components and Hardware Needed:

Qty

Carriage Bolts 5⁄16"-18 x 3⁄4"

14

Hex Nuts 5⁄16-18

14

Flat Washers 5⁄16"

14

Legs

4

Long Leg Braces

2

Short Leg Braces

2

Upper Stand Support

1

Tool Tray

1

Axle

1

Wheels

2

Cotter Pins

4

Transport Handle

1

Rubber Feet

2

Flat Washers 3⁄8"

4

Hex Nuts 3⁄8"-16

4

Flat Washers 5⁄8"

4

To assemble the stand:

 

1.Attach the short leg braces and then the long leg braces to the legs with carriage bolts, washers and hex nuts as shown in Figure 5.

Note: At this time, tighten with a 12mm wrench or socket just enough to secure the parts. Final tightening will take place when the stand is fully assembled.

Figure 5. Leg braces.

-16-

2.Secure the upper stand support to the inside of the legs using the carriage bolts. Start by securing the upper carriage bolt highlighted in Figure 6.

3.Attach the tool tray to the legs as shown in Figure 6. One side of the tool tray will share the lower carriage bolt of the upper stand support.

Upper Stand

Support

Leg

Tool Tray

Figure 6. Upper stand support and tool tray.

4.Slide the axle through the two holes at the bottom of the legs as shown in Figure 7.

5.Slide the wheels onto the axle with two 5⁄8" flat washers on either side of the wheel.

6.With a pair of pliers, insert a cotter pin through each hole at the end of the axle and bend back one end of the cotter pin to keep the wheel in place.

Figure 7. Axle and wheels.

G1010 4" x 6" Metal-Cutting Bandsaw

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model G1010 Page Table of Contents Maintenance ServiceWarranty and Returns Introduction ForewordContact Info Machine Data Sheet Other Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Metal-Cutting Bandsaws Wiring for Circuit Requirements110/220V Operation Grounding Extension CordsItems Needed for Set Up SET UPSet Up Safety UnpackingBox Contents Figure Qty InventoryItems not shown Hardware Recognition Chart Clean Up Site ConsiderationsStand Assembly Components and Hardware Needed QtyTo assemble the stand Mounting To mount the bandsaw to the standTo install the pulley cover Pulley CoverTo install the V-belt BeltUnplug the Bandsaw Vise Handwheel To install the handwheelTo install the work stop Work StopVertical Assembly Squaring table to bladeAdjusting table level Adjustments Factory adjustments that should be verifiedTest Run Recommended Operation Safety Blade Speed OperationsTo change blade speeds To adjust the feed rate Blade SelectionFeed Rate Vise To adjust the angle on the viseTo adjust the blade guides Blade GuidesOperation Tips Tips for horizontal cuttingTips for vertical cutting Accessories H5408-Blade Tensioning GaugeH1302-Standard Earmuffs H1302 H4979 H4977H1300 H1298 G7984 H2347 H0736 Schedule MaintenanceCleaning LubricationBlade Change To change the blade on the bandsawTo adjust the blade tracking on the bandsaw Blade TrackingBlade Tension Squaring the Blade To tension the blade on the bandsawTo square the blade to the bed of the table To adjust the blade guide bearings Blade Guide BearingsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService TroubleshootingSymptom Possible Cause Corrective Action Wiring Diagram G1010 G1010 Wiring diagram Plug Wire Switch WireParts Parts List G1010 DescriptionParts Breakdown G1010 Motor Mount Plate Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog
Top Page Image Contents