Grizzly G1010 instruction manual Safety Instructions for Machinery

Page 9

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

WILL result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

COULD result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

MAY result in minor or moderate injury. It may also be used to alert

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

3.ALWAYS WEAR AN ANSI APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery.

G1010 4" x 6" Metal-Cutting Bandsaw

-7-

Image 9
Contents Model G1010 Page Table of Contents Maintenance ServiceWarranty and Returns Introduction ForewordContact Info Machine Data Sheet Other Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Metal-Cutting Bandsaws Wiring for Circuit Requirements110/220V Operation Extension Cords GroundingSet Up Safety SET UPItems Needed for Set Up UnpackingBox Contents Figure Qty InventoryItems not shown Hardware Recognition Chart Site Considerations Clean UpStand Assembly Components and Hardware Needed QtyTo assemble the stand To mount the bandsaw to the stand MountingPulley Cover To install the pulley coverTo install the V-belt BeltUnplug the Bandsaw To install the work stop To install the handwheelVise Handwheel Work StopSquaring table to blade Vertical AssemblyAdjusting table level Adjustments Factory adjustments that should be verifiedTest Run Recommended Operation Safety Blade Speed OperationsTo change blade speeds To adjust the feed rate Blade SelectionFeed Rate To adjust the blade guides To adjust the angle on the viseVise Blade GuidesOperation Tips Tips for horizontal cuttingTips for vertical cutting H5408-Blade Tensioning Gauge AccessoriesH1302-Standard Earmuffs H1302 H4979 H4977H1300 H1298 G7984 H2347 H0736 Cleaning MaintenanceSchedule LubricationTo change the blade on the bandsaw Blade ChangeBlade Tracking To adjust the blade tracking on the bandsawBlade Tension Squaring the Blade To tension the blade on the bandsawTo square the blade to the bed of the table Blade Guide Bearings To adjust the blade guide bearingsDate Approximate Hours Of Use Maintenance Performed Maintenance LogTroubleshooting ServiceSymptom Possible Cause Corrective Action G1010 Wiring diagram Plug Wire Switch Wire Wiring Diagram G1010Parts Description Parts List G1010Parts Breakdown G1010 Motor Mount Plate Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog