Woodstock W1694 instruction manual Fence

Page 38

REF	PART #	DESCRIPTION

1	X1694001	FENCE
2	XPN06M	HEX NUT M5-.8
3	XPN01M	HEX NUT M6-1
4	XPB94M	HEX BOLT M5-.8 X 25
5	X1694005	HANDLE
6	X1694006	SPACER
7	X1694007	FENCE PLATE
8	XPLW04M	LOCK WASHER 8MM
9	XPSB14M	CAP SCREW M8-1.25 X 20
10	X1694010	PLATE SHAFT
11	X1694011	RIGHT LINK
12	X1694012	PUSH NUT M10
13	XPSB02M	CAP SCREW M6-1 X 20
14	XPLW03M	LOCK WASHER 6MM
15	X1694015	BRACKET SHAFT
16	X1694016	LEFT LINK
17	X1694017	FENCE BRACKET
18	XPSB37M	CAP SCREW M6-1 X 50
19	X1694019	LIMIT PLATE
20	X1694020	SHAFT
21	X1694021	BLOCK
22	X1694022	HANDLE
23	X1694023	INFEED TABLE
24	X1694024	BRACKET

REF	PART #	DESCRIPTION

25	X1694025	TABLE PIN
26	X1694026	FRAME PIN
27	X1694027	FENCE SUPPORT
28	X1694028	PIN
29	X1694029	LOCKING PLATE
30	XPN03M	HEX NUT M8-1.25
31	XPB20M	HEX BOLT M8-1.25 X 35
32	X1694032	TABLE FRAME
33	X1694033	3CMI-6 E-RING
34	XPSS28M	SETSCREW M6-1 X 30
35	XPSS29M	SETSCREW M6-1 X 35
36	X1694036	SUPPORT PLATE
37	XPLW01M	LOCK WASHER 5MM
38	XPSS11M	SETSCREW M6-1 X 16
39	XPSW03-1	KNOB
40	X1694040	ELEVATION SCREW
41	XPW02M	FLAT WASHER 5MM
42	XPSS11M	SETSCREW M6-1 X 16
43	XPW03M	FLAT WASHER 6MM
44	XPS09M	PHLP HD SCR M5-.8 X 10
45	XPSB07M	CAP SCREW M6-1 X 30
46	X1694046	PUSH BLOCK (SET OF 2)
47	XPSS28M	SETSCREW M6-1 X 30

-36-

Image 38

Contents Bench TOP Jointer Page Contents About Your New Jointer Woodstock Service and SupportIntroduction Warranty and Returns SpecificationsSafety Standard Safety Instructions#16 #14 11-12 13-16 #12 17-20 #10 21-30 Know Your Machine Safety Instructions for Your Jointer Avoiding Potential Injuries Never surface plane without push blocksGrounding Electrical Requirements110V Operation Extension CordsInventory AssemblyUnpacking Dust Collection Initial CleaningShop Preparation To attach the rubber feet, do these steps Rubber FeetFence Support To attach the fence support, do these stepsFence Assembly To assemble the fence assembly, do these stepsDust Port To install the 90˚ stop slide, do these steps90˚ Stop Slide To connect the dust port to a trash bag, do these steps Assembling the trash bag supportAdjustments FenceSetting the fence to 90˚ Fence Angle StopsTo adjust the 45˚ inward angle stop bolt, do these steps To adjust the 45˚ outward angle stop bolt, do these stepsBlade Height To check the cutterhead blade height, do these stepsTo adjust the depth of cut Depth Of CutBlade Guard Blade guard in useTo test run the Model W1694, do these steps OperationsTest Run Operation Requirements Correct and incorrect grain Alignment to cutterheadOperation Requirements sub-section Surface PlaningTo perform a surface planing operation, do these steps Edge Jointing To perform an edge jointing operation, do these stepsBevel Cutting To perform a bevel cutting operation, do theseTable Surface MaintenanceGeneral Sharpening BladesReplacing Blades To replace the cutterhead blades, do these stepsTo replace a worn out blade guard spring, do these steps Guard SpringLubrication To replace the drive belts, do these steps Drive BeltsMotor Brushes Troubleshooting Chipping occurs on workpiece Closure W1694 Wiring Diagram Parts Fence Page Base with Outfeed Table Warranty Card BOX BELLINGHAM, WA

Related manuals

Manual 44 pages 48.28 Kb