Woodstock W1694 instruction manual Standard Safety Instructions

Page 6

SAFETY

SAFETY

READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY.

Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury, MAY result in property damage.

This symbol is used to alert the user to useful information about proper NOTICE operation of the equipment.

Standard Safety Instructions

1.Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future reference.

2.Keep work area clean and well lit. Clutter and inadequate lighting invite potential hazards.

3.Ground all tools. If a machine is equipped with a three-prong plug, it must be plugged into a three- hole grounded electrical receptacle or grounded extension cord. If using an adapter to aid in accom- modating a two-hole receptacle, ground using a screw to a known ground.

4.Wear eye protection at all times. Use safety glasses with side shields or safety goggles that meet the appropriate standards of the American National Standards Institute (ANSI).

5.Avoid dangerous environments. DO NOT operate this machine in wet or open flame environments. Airborne dust particles could cause an explosion and severe fire hazard.

6.Ensure all guards are securely in place and in working condition.

7.Make sure the machine power switch is in the OFF position before connecting power to machine.

8.Keep the work area clean, free of clutter, grease, etc.

9.Keep children and visitors away. Visitors should be kept at a safe distance while operating unit.

10.Childproof your workshop with padlocks, master switches or by removing starter keys.

11.Stop and disconnect the machine when cleaning, adjusting or servicing.

-4-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Bench TOP Jointer Page Contents Woodstock Service and Support IntroductionAbout Your New Jointer Warranty and Returns SpecificationsSafety Standard Safety Instructions#16 #14 11-12 13-16 #12 17-20 #10 21-30 Know Your Machine Safety Instructions for Your Jointer Avoiding Potential Injuries Never surface plane without push blocksGrounding Electrical Requirements110V Operation Extension CordsAssembly UnpackingInventory Initial Cleaning Shop PreparationDust Collection To attach the rubber feet, do these steps Rubber FeetFence Support To attach the fence support, do these stepsFence Assembly To assemble the fence assembly, do these stepsTo install the 90˚ stop slide, do these steps 90˚ Stop SlideDust Port To connect the dust port to a trash bag, do these steps Assembling the trash bag supportAdjustments FenceSetting the fence to 90˚ Fence Angle StopsTo adjust the 45˚ inward angle stop bolt, do these steps To adjust the 45˚ outward angle stop bolt, do these stepsBlade Height To check the cutterhead blade height, do these stepsTo adjust the depth of cut Depth Of CutBlade Guard Blade guard in useOperations Test RunTo test run the Model W1694, do these steps Operation Requirements Correct and incorrect grain Alignment to cutterheadSurface Planing To perform a surface planing operation, do these stepsOperation Requirements sub-section Edge Jointing To perform an edge jointing operation, do these stepsBevel Cutting To perform a bevel cutting operation, do theseTable Surface MaintenanceGeneral Sharpening BladesReplacing Blades To replace the cutterhead blades, do these stepsGuard Spring LubricationTo replace a worn out blade guard spring, do these steps Drive Belts Motor BrushesTo replace the drive belts, do these steps Troubleshooting Chipping occurs on workpiece Closure W1694 Wiring Diagram Parts Fence Page Base with Outfeed Table Warranty Card BOX BELLINGHAM, WA
Related manuals
Manual 44 pages 48.28 Kb
Top Page Image Contents