Woodstock W1694 instruction manual Warranty and Returns, Specifications

Page 5

Warranty and Returns

Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work- manship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or acci- dents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone other than Woodstock International, Inc.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facil- ity designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this war- ranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequen- tial damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabili- ty standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

 

Specifications

Motor Size

2 HP, 110V, Universal-Type Motor

Motor Speed

10,000 RPM

Amp Draw

12 A

Maximum Cutting Depth

1⁄8"

Maximum Cutting Width

61⁄8"

Minimum Cutting Length

81⁄8"

Cutterhead Blades

2 HSS

Machine Weight

921⁄2 lbs

NTRODUCTION

-3-

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Bench TOP Jointer Page Contents About Your New Jointer Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsStandard Safety Instructions Safety#16 #14 11-12 13-16 #12 17-20 #10 21-30 Know Your Machine Safety Instructions for Your Jointer Never surface plane without push blocks Avoiding Potential Injuries110V Operation Electrical RequirementsGrounding Extension CordsInventory AssemblyUnpacking Dust Collection Initial CleaningShop Preparation Fence Support Rubber FeetTo attach the rubber feet, do these steps To attach the fence support, do these stepsTo assemble the fence assembly, do these steps Fence AssemblyDust Port To install the 90˚ stop slide, do these steps90˚ Stop Slide Assembling the trash bag support To connect the dust port to a trash bag, do these stepsFence AdjustmentsFence Angle Stops Setting the fence to 90˚To adjust the 45˚ outward angle stop bolt, do these steps To adjust the 45˚ inward angle stop bolt, do these stepsTo check the cutterhead blade height, do these steps Blade HeightDepth Of Cut To adjust the depth of cutBlade guard in use Blade GuardTo test run the Model W1694, do these steps OperationsTest Run Correct and incorrect grain Alignment to cutterhead Operation RequirementsOperation Requirements sub-section Surface PlaningTo perform a surface planing operation, do these steps To perform an edge jointing operation, do these steps Edge JointingTo perform a bevel cutting operation, do these Bevel CuttingGeneral MaintenanceTable Surface Sharpening BladesTo replace the cutterhead blades, do these steps Replacing BladesTo replace a worn out blade guard spring, do these steps Guard SpringLubrication To replace the drive belts, do these steps Drive BeltsMotor Brushes Troubleshooting Chipping occurs on workpiece Closure W1694 Wiring Diagram Parts Fence Page Base with Outfeed Table Warranty Card BOX BELLINGHAM, WA
Related manuals
Manual 44 pages 48.28 Kb
Top Page Image Contents