Banner L-GAGE manual GAGEQ50 Analog Output Specifications, Supply Voltage and Current, Resolution

AREA&
LIGHT GAUGING
PART
LABEL&
ULTRASONIC
SLOT
MEASURING	lUMINESCENCE
SCREENS
&
COLOR
LIGHT
TEMPERATURE
LIGHT-TO-
PICK
RADAR

MEASUREMENT & INSPECTION

L-GAGE®Q50 Analog Output Specifications

Sensing Beam	Wavelength:	Q50..V: 685 nm (typical)			Q50..: 880 nm (typical)
	Beam Size:	Q50..V: 20 mm dia. (max.)			Q50..: 20 mm dia. (max.)
Sensing Range	Q50AV: 50 to 150 mm				Q50A: 50 to 200 mm
	Q50BV: 100 to 300 mm				Q50B: 100 to 400 mm
Supply Voltage and Current	15 to 30V dc (10% max. ripple); 70 mA max. (exclusive of load)
Supply Protection Circuitry	Protected against reverse polarity and transient overvoltages
Output Configuration	4-20 mA current sourcing models: 1 kΩ max. load @ 24V dc. Max. load = [(Vcc -4.5)/0.02]Ω
	0-10V voltage sourcing models: 15 mA max.
Delay at Power-up	2 seconds
Output Protection	Protected against short circuit conditions
Output Response Time	Analog Output		Average Interval		Update Rate	-3 dB Frequency Response
	Fast:			4 milliseconds	1 millisecond		112 Hz
	Slow:		64 milliseconds		4 milliseconds		7 Hz
Resolution	See RRC-5 and RRC-6 on page 510 for typical value.
	Q50B models:
	Target Distance: 200 mm Slow Response: 1 mm (max) Fast Response: 4 mm (max)
	Q50A models:
	Target Distance: 100 mm Slow Response: 0.5 mm (max) Fast Response: 2 mm (max)
Linearity	Q50B.. models: ±3 mm			Q50A.. models: ±1.5 mm
Color Sensitivity (typical)	See charts CSC-4 and CSC-5 on page 511.
Temperature Effect	Q50B.. models:				From -10° to 55° C: 0.35 mm/° C
	From 0° to 50° C: 0.25 mm/° C
	Q50A.. models:
	From 0° to 50° C: 0.08 mm/° C				From -10° to 55° C: 0.11 mm/° C
Remote and Speed Input	15 kΩ
Impedance
Remote TEACH Input	To Teach: Connect gray wire to +5 to 30V dc
	To Disable: Connect gray wire to 0 to +2V dc (or open connection)
Adjustments	Fast Speed: Connect black wire to +5 to 30V dc
	Slow Speed: Connect black wire to 0 to +2V dc (or open connection)
Indicators	Range LED		Green — Target is within sensing range
	Indicator		Red — Target is outside sensing range
	(Green/Red)		OFF — Sensor Power OFF
	Teach/Output		Yellow — Target is within taught window limits
	LED Indicator		OFF — Target is outside taught window limits
	(Yellow/Red)		Red — Sensor is in TEACH mode
Ambient Light Immunity	< 10,000 LUX
Construction	Housing: Molded ABS/Polycarbonate				Hardware: M3 hardware is included.		Window Lens: Acrylic
Environmental Rating	IEC IP67; NEMA 6P
Connections	2 m or 9 m 5-conductor PVC-covered attached cable, or 5-pin Euro-style quick-disconnect.
	See page 416.
Operating Conditions	Temperature: -10° to +55° C Relative humidity: 90% at +50° C (non-condensing)
Vibration and	All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max. double amplitude
Mechanical Shock	0.06”, maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G,
	11 milliseconds duration, half sine wave.
Application Notes	Allow 15-minute warm-up for maximum performance
Certifications
Hookup Diagrams	MI09 (p. 534)

260 More information online at bannerengineering.com