Banner L-GAGE GAGEQT50U DC Specifications cont’d, GAGEQT50U Universal Voltage Specifications, 265

			MEASUREMENT & INSPECTION
		U-GAGE®QT50U DC Specifications (cont’d)
Certifications
Hookup Diagrams		Analog Models: MI11 (p. 534)	Discrete Models: MI10 (p. 534)
U-GAGE®QT50U Universal Voltage Specifications
Effective Beam	See charts EBPC-1, EBPC-2 and EBPC-3 on page 513.
Supply Voltage	85 to 264V ac, 50/60 Hz / 24 to 250V dc (1.5 watts max., exclusive of load)
Ultrasonic Frequency	75 kHz burst, rep. rate 96 milliseconds.
Supply Protection	Protected against transient over voltages. DC hookup is without regard to polarity.
Circuitry
Output Protection	Protected against short circuit conditions
Delay at Power-up	1.5 seconds
Output Configuration	SPDT (Single-Pole, Double-Throw) electromechanical relay output.
	One normally open (NO) and one normally closed (NC).
Output Ratings	Max. switching power (resistive load): 2000 VA, 240 W (1000 VA, 120 W for sensors with Micro QD)
	Max. switching voltage (resistive load): 250V ac, 125V dc
	Max. switching current (resistive load): 8A @ 250V ac, 8A @ 30V dc derated to 200 mA @ 125V dc
	(4A max. for sensors with Micro QD)
	Min. voltage and current: 5V dc, 10 mA
	Mechanical life of relay: 50,000,000 operations
	Electrical life of relay at full resistive load: 100,000 operations
	NOTE: Transient suppression is recommended when switching inductive loads.
Temperature Effect	Uncompensated: 0.2% of distance/° C		Compensated: 0.02% of distance/° C
Repeatability	1.0 mm
Hysteresis	Window-limit sensor models: 5 mm		Fill-level control sensor models: 0 mm
Output Response Time	Selectable 1600, 400 or 100 milliseconds
Minimum Window Size	20 mm
Adjustments	Sensing limits: TEACH-Mode programming of near and far limits may be set using the TEACH push button.
	Sensor configuration: Output response time and temperature compensation mode may be set using
	the Speed push button.
	Factory default settings: 400 milliseconds output response time; temperature compensation enabled
Indicators	Green Power ON LED: Indicates power is ON
	Red Signal LED: Indicates target is within sensing range, and the condition of the received signal.
	Output indicator (bicolor Yellow/Red): Indicates output status or TEACH mode
	Response indicator (bicolor Yellow/Red): Indicates output response time selection
Construction	Transducer: Ceramic/Epoxy composite		Housing: ABS
	Membrane Switch: Polyester
Environmental Rating	Leakproof design is rated IEC IP67; NEMA 6P
Connections	2 m or 9 m shielded 5-conductor (with drain) PVC jacketed attached cable, or 5-pin Micro-style
	quick-disconnect or 5-pin Mini-style quick-disconnect. QD cables are ordered separately.
	See pages 419 and 421.
Operating Conditions	Temperature: -20° to +70° C		Relative humidity: 100%
Vibration and	All models meet Mil Std. 202F requirements. Method 201A (vibration: 10 to 60Hz max.,
Mechanical Shock	double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G
	11 milliseconds duration, half sine wave
Temperature Warmup Drift	Less than 1.0% of sensing distance upon power-up with Temperature Compensation enabled
Application Notes	Objects passing inside the specified minimum sensing distance (200 mm) may produce a false response.
Certifications	Contact factory for more information.
Hookup Diagrams	UN05 (p. 529)

Teflon® is a registered trademark of Dupont™

LIGHT ULTRASONIC MEASURING LIGHT TEMPERATURE RADAR GAUGINGSCREENS

More information online at bannerengineering.com 265