Banner L-GAGE manual GAGEEZ-ARRAYSpecification

PICK-TO-LIGHT SCREENSGAUGING

RADAR TEMPERATURE MEASURING LIGHT ULTRASONIC LIGHT

MEASUREMENT & INSPECTION

A-GAGE®EZ-ARRAY™Specification

Supply Voltage (Limit Values)	Emitter: 12 to 30V dc
	Receiver Analog Current Models: 12 to 30V dc		Receiver Analog Voltage Models: 15 to 30V dc
Supply Power Requirements	Emitter/Receiver Pair (Exclusive of discrete load): Less than 9 watts				Power-up delay: 2 seconds
Emitter/Receiver Range	400 mm to 4 m
Field of View	Nominally ± 3°
Beam Spacing	5 mm
Light Source	Infrared LED
Minimum Object	Straight Scan, Low-Contrast: 5 mm
Detection Size	Straight Scan, High-Excess-Gain: 10 mm
Sensor Positional Resolution	Straight Scan: 5 mm Double-Edge Scan: 2.5 mm Single-Edge Scan: 2.5 mm
Teach Input	Low: 0 to 2 volts High: 6 to 30 volts or open (input impedance 22 kΩ)
(Receiver Gray Wire)
Two Discrete Outputs	Solid-State NPN or PNP (current sinking or sourcing)
	Rating: 100 mA max. each output
	OFF-State Leakage Current: NPN: less than 200 uA @ 30V dc			PNP: less than 10 uA @ 30V dc
	ON-State Saturation Voltage: NPN: less than 1.6V @ 100 mA			PNP: less than 2.0V @ 100 mA
	Protected against false pulse on power-up and continuous overload or short circuit.
Two Analog Outputs	Voltage Sourcing: 0 to 10V (maximum current load of 5 mA)
	Current Sourcing: 4 to 20 mA (maximum resistance load = (Vsupply–3) / 0.020)
Serial Communication	EIA-485 Modbus RTU (up to 15 nodes per communication ring)
Interface	RTU binary format
	Baud Rate: 9600, 19.2K or 38.4K
	8 Data Bits, 1 Stop Bit, and Even, Odd, or 2 Stop Bits and No Parity
Scan Time	Scan times depend on scan mode and sensor length. Straight scan times range from 2.8 to 26.5 milliseconds.
Status Indicators	Emitter: Red Status LED
	ON Steady—Status OK		Flashing at 1 hz—Error
	Receiver:
	7 Zone Indicators
	Red—Blocked channels within zone		Green—All channels clear within zone
	3-digit 7-segment indicators for measurement mode / diagnostic information
	Sensor Status Bicolor Indicator LED
	Red—Hardware Error or Marginal Alignment		Green—OK
	Modbus Activity Indicator LED: Yellow
	Modbus Error Indicator LED: Red
System Configuration	6-position DIP switch: Used to set scanning type, measurement modes, analog slope and discrete output
(Receiver Interface)	2 function. Alternate software GUI interface provides additional options; see full manual (p/n 130426).
Push Buttons	Two momentary push buttons for alignment and gain level selection.
(Receiver Interface)
Connections	Serial communication: The receiver uses a PVC-jacketed, 5-conductor 22-gauge quick-disconnect cable,
	5.4 mm diameter. QD cables are ordered separately. See page 422.
	Other Sensor connections: 8-conductor quick-disconnect cables (one each for emitter and receiver),
	ordered separately (may not exceed 75 m long), PVC-jacketed cables measure 5.8 mm diameter, have
	shield wire; 22-gauge conductors. QD cables are ordered separately. See page 416.
Construction	Aluminum housing with clear-anodized finish; acrylic lens cover
Environmental Rating	IEC IP65
Operating Conditions	Temperature: –40° to +70° C	Relative humidity: 95% at 50° C (non-condensing)
Hookup Diagrams	NPN models: MI23 (p. 537)	PNP models: MI24 (p. 537)

290 More information online at bannerengineering.com