Banner L-GAGE manual Gage MINI-ARRAY Controller Specifications cont’d

PICK-TO-LIGHT SCREENSGAUGING

RADAR TEMPERATURE MEASURING LIGHT ULTRASONIC LIGHT

MEASUREMENT & INSPECTION

A-GAGE®MINI-ARRAY®Controller Specifications (cont’d)
Construction	Polycarbonate
Environmental Rating	NEMA 1; IP20
Operating Conditions	Temperature: -20° to +70° C Relative humidity: 95% (non-condensing)
Certifications		R
Hookup Diagram	MAC-1:MI27 (p. 538)				MACN-1/MACP-1: MI28 (p. 538)
	MACV-1/MACI-1: MI29 (p. 539)				MAC16N-1/MAC16P-1:MI31 (p. 539)
A-GAGE®MINI-ARRAY®Controller with DeviceNet™ Specifications
DeviceNet Configurations		Vendor code:	12 (Banner Corp.)
		Device type:	110
		Product code: 1 (MACNXDN-1)
			2 (MACPXDN-1)
		Connection types supported: Explicit Message, Poll, COS
		Network address: 0-63 (network configured), default = 63
		Baud rate supported: 125K, 250K, 500K (network configured), default = 125K
Output Configurations		MACPXDN-1:Two PNP discrete (switched)
		MACNXDN-1:Two NPN discrete (switched)
Power Requirements*		Controller, emitter and receiver: 16 to 30V dc @ 1.2 A max. (typical: 0.5 A @ 16V dc)
DeviceNet Power*		11 to 25V dc - supplied by DeviceNet BUS Network
Inputs		Sensor input: Emitter and receiver wire in parallel to five terminals.
		Trigger (Gate) input: Optically isolated, requires 10 to 30V dc (7.5 kΩ impedance) for gate signal
Discrete Outputs		NPN outputs:		Open collector NPN transistor rated at 30V dc max., 150 mA max.
		PNP outputs:		Open collector PNP transistor rated at 30V dc max., 150 mA max.
		All discrete outputs: OFF-state leakage current: less than 10 µA @ 30V dc
				ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5V @ 150 mA
System Programming		Via DeviceNet interface and supplied EDS files.
System Status Indicators		Output (steady red):		Output #1 energized.
		Alarm (flashing red):		Output #2 energized.
		Gate (steady red):		Trigger (Gate) input status.
		Alignment (steady green): Proper emitter/receiver alignment and a clear, unblocked light screen
				(ON) when green or green/yellow receiver LEDs are ON.
		Diag 1 (Green), Diag 2 (Red), Diag 3 (Red): Used in combination to display System status
Network Status Indicator		Bicolored (Red/Green) LED visible on the control module front panel indicates network status:
		Steady Green: On-line, connected to master
		Flashing Green: On-line, address and baud rate OK
		Steady Red:	Critical network fault or duplicate node address detected
		Flashing Red:	Connection timeout
		OFF:	No network power or off-line
Construction		Polycarbonate housing; mounts to flat surface or directly onto 35-mm DIN rail
Environmental Rating		NEMA 1; IP20
Operating Conditions		Temperature: -20° to +70° C			Relative humidity: 95% @ 50° C (non-condensing)
*Application Note		The controller must be powered up before the DeviceNet connection in every power-up situation for
		proper operation
Hookup Diagrams		MI30 (p. 539)

DeviceNet™ is a trademark of the Open DeviceNet Vendor Association, Inc.

300 More information online at bannerengineering.com