InFocus M-300 manual FCC Compliance Statement and Warnings

Page 12

1-6 Safety

FCC Compliance

This ULS laser system has been tested and found to comply with Federal Communication Commission (FCC) directives regarding Electromagnetic Compatibility (EMC). In accordance with these directives ULS is required to provide the following information to its customers.

FCC Compliance Statement and Warnings

This device Complied with FCC Rules Part 15. Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device as set forth in Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.

Users should be aware that changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

This equipment has been type tested and found to comply with the limits for a Computing Device per FCC part 15, using shielded cables. Shielded cables must be used in order to insure compliance with FCC regulations.

Image 12
Contents Laser Platform Universal Laser Systems Inc All Rights Reserved Introduction Table of Contents Options & Accessories Sample MaterialsMaintenance TroubleshootingAppendices General Safety Description of Appropriate UseLaser Safety SafetySafety Labels AB C DOr D UL-30 FCC Compliance FCC Compliance Statement and WarningsEU Compliance CE EU Declaration of ConformityInstallation Operating EnvironmentInstallation Electrical RequirementsExhaust Requirements Gate Cart Assembly Installation Laser Cartridge Installation Installation Laser Cooling Requirements Computer RequirementsSoftware Suggestions Graphics ProgramsFont Requirements Making the Connections Problem Prevention Computer Controlling the Laser SystemDC Power Supply How it WorksControl Panel Laser Cartridge System Operation Laser CartridgeControl Panel System OperationMotion System System Operation Liquid Crystal Display LCD System Operation Green Indicator Light Red Indicator LightProcess Controls Motion Control System Menu System System Operation Menu Descriptions Ready MenuSystem Operation File Display Menu Main Menu Memory Control MenuSystem Operation System Operation DOS Power Settings Menu Preferences MenuSystem Operation Options Menu ONE File Memory MenuHelpful Hint Autofocus MenuConfiguration Menu System Operation AIR Assist MenuDual Head Menu SET Focus Position MenuSET Rotary Axis Menu Tickle Menu Ports MenuLanguage Menu Units MenuSystem Operation Diagnostics Menu Alignment Mode MenuMemory Test Menu Motor Status DisplayAbout Menu Focusing the Laser Beam Focus Tool Method Material Thickness Z Position Method Current Lens MenuSET Focal Height Menu System Operation Autofocus Method To Use AutofocusTo Adjust Autofocus Powering Up Loading and Positioning the MaterialFocusing Running the System Step by StepSetting the Drivers Properties Creating the GraphicDownloading the File Starting the Engraving Process Material Removing and Reloading 3D Effects Rubber StampsSingle Stamp Method Options & Accessories Place Stamp in AN Unused AreaOptions & Accessories Settings for a 30 Watt System Options & Accessories Full Sheet Method Rotary Fixture Cutting Table Air Assist System Air Assist CompressorFocus Lens Kits Focal Length Spot Size Focal Range Safety Sample MaterialsMaterials Sample MaterialsSample Materials Light Raster Engraving Comments Acrylic Mirrored Comments Raster Engraving Brass Painted Corian / Avonite / Fountainhead Cork Male Female Glass / Crystal Leather Marble MAT Board Melamine Standard Engraving Melamine PHOTO/CLIPART Engraving Plastic Engravers Microsurfaced Perforated Vector Cutting Vector Cutting Kiss CUT Wood Laser Engraving or Cutting Wood can Ignite the Material Maintenance Suggested Cleaning and Maintenance SuppliesMaintenance System Cleaning Optics CleaningMaintenance #2 Mirror Maintenance #3 Mirror and Focus Lens Maintenance Beam Window Autofocus Sensor and Reflector if installedAdjustments and Lubrication Fuse ReplacementBattery Replacement Electronic UpgradingMaintenance Schedule Cooling Fan FiltersTroubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Operational Ihr ULS Vertragshändler Appendix Appendix a Limited Warranty Appendix B Specifications Facility RequirementsAppendix C Using DOS Based Programs Appendix D Using Macintosh Computers Appendix E Serial Port Cable Requirements Appendix F How To Get Help Step