InFocus M-300 manual Maintenance #3 Mirror and Focus Lens

Page 92

Maintenance 7-5

#3 Mirror and Focus Lens

You must remove the front cover to the Focus Carriage to gain access to the #3 Mirror and the Focus Lens. To do this, hold the front cover with one hand and with the other hand, remove the three(3) thumbscrews that attach the front cover to the Focus Carriage, and pull the front cover straight out. You will notice that the #3 Mirror and the Focus lens are both mounted to the front cover. Refer to the diagram below.

The #3 Mirror and the Focus lens are both glued to a metal bracket and the metal bracket is attached to the front plate with Phillips head screws. It is not necessary to detach the bracket from either optic in order to clean them. Simply tilt the front cover at enough angle so that you can apply the Lens Cleaning solution directly to the #3 Mirror and to the Focus Lens. Flood the surfaces with the solution. If heavy debris is present, let the solution soak in for a minute. Roll a fresh cotton swab across the #3 Mirror to dry it off. Remember that it is okay if a small amount of lint from the cotton swab remains on the mirror. Repeat this procedure for the Focus lens and always use a fresh swab.

Image 92
Contents Laser Platform Universal Laser Systems Inc All Rights Reserved Introduction Table of Contents Options & Accessories Sample MaterialsAppendices MaintenanceTroubleshooting General Safety Description of Appropriate UseLaser Safety SafetySafety Labels AB C DOr D UL-30 FCC Compliance FCC Compliance Statement and WarningsEU Compliance CE EU Declaration of ConformityInstallation Operating EnvironmentInstallation Electrical RequirementsExhaust Requirements Gate Cart Assembly Installation Laser Cartridge Installation Installation Laser Cooling Requirements Computer RequirementsSoftware Suggestions Graphics ProgramsFont Requirements Making the Connections Problem Prevention Computer Controlling the Laser SystemControl Panel DC Power SupplyHow it Works Laser Cartridge System Operation Laser CartridgeMotion System Control PanelSystem Operation System Operation Liquid Crystal Display LCD Process Controls System Operation Green Indicator LightRed Indicator Light Motion Control System Menu System System Operation Menu Descriptions Ready MenuSystem Operation File Display Menu Main Menu Memory Control MenuSystem Operation System Operation DOS Power Settings Menu Preferences MenuSystem Operation Options Menu ONE File Memory MenuHelpful Hint Autofocus MenuConfiguration Menu System Operation AIR Assist MenuDual Head Menu SET Focus Position MenuSET Rotary Axis Menu Tickle Menu Ports MenuLanguage Menu Units MenuSystem Operation Diagnostics Menu Alignment Mode MenuMemory Test Menu Motor Status DisplayAbout Menu Focusing the Laser Beam Focus Tool Method SET Focal Height Menu Material Thickness Z Position MethodCurrent Lens Menu System Operation Autofocus Method To Use AutofocusTo Adjust Autofocus Powering Up Loading and Positioning the MaterialFocusing Running the System Step by StepDownloading the File Setting the Drivers PropertiesCreating the Graphic Starting the Engraving Process Material Removing and Reloading Single Stamp Method 3D EffectsRubber Stamps Options & Accessories Place Stamp in AN Unused AreaOptions & Accessories Settings for a 30 Watt System Options & Accessories Full Sheet Method Rotary Fixture Cutting Table Air Assist System Air Assist CompressorFocus Lens Kits Focal Length Spot Size Focal Range Safety Sample MaterialsMaterials Sample MaterialsSample Materials Light Raster Engraving Comments Acrylic Mirrored Comments Raster Engraving Brass Painted Corian / Avonite / Fountainhead Cork Male Female Glass / Crystal Leather Marble MAT Board Melamine Standard Engraving Melamine PHOTO/CLIPART Engraving Plastic Engravers Microsurfaced Perforated Vector Cutting Vector Cutting Kiss CUT Wood Laser Engraving or Cutting Wood can Ignite the Material Maintenance Suggested Cleaning and Maintenance SuppliesMaintenance System Cleaning Optics CleaningMaintenance #2 Mirror Maintenance #3 Mirror and Focus Lens Maintenance Beam Window Autofocus Sensor and Reflector if installedAdjustments and Lubrication Fuse ReplacementBattery Replacement Electronic UpgradingMaintenance Schedule Cooling Fan FiltersTroubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Operational Ihr ULS Vertragshändler Appendix Appendix a Limited Warranty Appendix B Specifications Facility RequirementsAppendix C Using DOS Based Programs Appendix D Using Macintosh Computers Appendix E Serial Port Cable Requirements Appendix F How To Get Help Step