InFocus M-300 manual Installation

Page 19
Adjust spacing if front door comes in contact with legs.
E L BB BU
EL LEV
LIFT HERE
(SAME FOR OTHER SIDE)

2-6 Installation

9. Note the lifting points as shown. With the assistance of one or two other people, carefully lift the laser system and place it onto the cart assembly being careful not to drop it or pinch your fingers.

10. Thread the remaining two screws and lockwashers (C) through the tabs on the back panel (A) and into the backside of the laser system. Do not tighten down completely yet.

11.Thread the 4 screws and flat washers

(H) through the underside of the legs and into the bottom of the laser system. Do

not tighten down completely yet.

12. Gently open the front door and see if it comes in contact with the bottom part of the legs.

13.Space the legs apart to provide clearance for the front door.

14. Securely tighten all remaining screws

(C) and (H).

15. Relocate the laser system to its final resting position next to the computer and exhaust system.

16. If the floor underneath the laser system is uneven, the casters must be adjusted.

Refer to the following leveling instructions. Place a bubble level across

the top of the legs directly above the front casters. Note the bubble position in its

sight glass. Do the same for the back part of the legs and also note the position of the bubble in the sight glass. If the

bubbles are in the same visual position, adjustment is not necessary and cart

assembly is complete. If they are in different positions, adjustment is required.

17.To adjust the casters, choose ONLY ONE (1) caster and adjust its height until both bubbles are visually identical between the front casters and the back casters. The purpose of this step is to make sure that all casters lie in the same plane, not to level the laser system with the ground. If desired, you can level the laser system with the ground although it is not required.

18.Open the top door and remove the rubber band that is holding the arm in place.

19.Remove any remaining packing materials, accessories or any other items that may be located inside the cabinet or on top of the engraving table.

20.Gain access to the rear of the laser system to install the Laser Cartridge.

Image 19
Contents Laser Platform Universal Laser Systems Inc All Rights Reserved Introduction Table of Contents Sample Materials Options & AccessoriesTroubleshooting MaintenanceAppendices Description of Appropriate Use General SafetySafety Laser SafetyAB C D Safety LabelsOr D UL-30 FCC Compliance Statement and Warnings FCC ComplianceEU Declaration of Conformity EU Compliance CEOperating Environment InstallationElectrical Requirements InstallationExhaust Requirements Gate Cart Assembly Installation Laser Cartridge Installation Installation Graphics Programs Laser Cooling RequirementsComputer Requirements Software SuggestionsFont Requirements Making the Connections Computer Controlling the Laser System Problem PreventionHow it Works DC Power SupplyControl Panel System Operation Laser Cartridge Laser CartridgeSystem Operation Control PanelMotion System System Operation Liquid Crystal Display LCD Red Indicator Light System Operation Green Indicator LightProcess Controls Motion Control System Menu System System Operation Ready Menu Menu DescriptionsSystem Operation File Display Menu Memory Control Menu Main MenuSystem Operation Preferences Menu System Operation DOS Power Settings MenuAutofocus Menu System Operation Options MenuONE File Memory Menu Helpful HintSET Focus Position Menu Configuration MenuSystem Operation AIR Assist Menu Dual Head MenuSET Rotary Axis Menu Ports Menu Tickle MenuUnits Menu Language MenuMotor Status Display System Operation Diagnostics MenuAlignment Mode Menu Memory Test MenuAbout Menu Focusing the Laser Beam Focus Tool Method Current Lens Menu Material Thickness Z Position MethodSET Focal Height Menu To Use Autofocus System Operation Autofocus MethodTo Adjust Autofocus Loading and Positioning the Material Powering UpRunning the System Step by Step FocusingCreating the Graphic Setting the Drivers PropertiesDownloading the File Starting the Engraving Process Material Removing and Reloading Rubber Stamps 3D EffectsSingle Stamp Method Place Stamp in AN Unused Area Options & AccessoriesOptions & Accessories Settings for a 30 Watt System Options & Accessories Full Sheet Method Rotary Fixture Cutting Table Air Assist Compressor Air Assist SystemFocus Lens Kits Focal Length Spot Size Focal Range Sample Materials SafetySample Materials MaterialsSample Materials Light Raster Engraving Comments Acrylic Mirrored Comments Raster Engraving Brass Painted Corian / Avonite / Fountainhead Cork Male Female Glass / Crystal Leather Marble MAT Board Melamine Standard Engraving Melamine PHOTO/CLIPART Engraving Plastic Engravers Microsurfaced Perforated Vector Cutting Vector Cutting Kiss CUT Wood Laser Engraving or Cutting Wood can Ignite the Material Suggested Cleaning and Maintenance Supplies MaintenanceMaintenance Optics Cleaning System CleaningMaintenance #2 Mirror Maintenance #3 Mirror and Focus Lens Autofocus Sensor and Reflector if installed Maintenance Beam WindowElectronic Upgrading Adjustments and LubricationFuse Replacement Battery ReplacementCooling Fan Filters Maintenance ScheduleTroubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Operational Ihr ULS Vertragshändler Appendix Appendix a Limited Warranty Facility Requirements Appendix B SpecificationsAppendix C Using DOS Based Programs Appendix D Using Macintosh Computers Appendix E Serial Port Cable Requirements Step Appendix F How To Get Help