InFocus M-300 manual Laser Safety

Page 8

1-2 Safety

Care should be taken when moving or lifting this device. Obtain assistance from 1 or 2 additional people when lifting or carrying. Severe bodily injury may occur if improper lifting techniques are applied. Be careful not to drop the unit. Not only can it cause bodily harm, but it can also severely damage the equipment and render it inoperable.

This device is specifically designed to comply with CDRH performance requirements under 21 CFR 1040.10 and 1040.11. CDRH is the Center for the Devices of Radiological Health division of the Food and Drug Administration (FDA). It also complies with CE (European Community) safety regulations. No guarantees of suitability or safety are provided for any use other than those specified by Universal Laser Systems Inc. Please contact Universal Laser Systems Inc. with any questions concerning laser safety before operating this system.

Laser Safety

The laser system contains a sealed carbon dioxide (CO2) laser that produces intense and invisible laser radiation at a wavelength of 10.6 microns in the infrared spectrum. This laser system contains a C02 laser in a Class I enclosure. However, due to the presence of a visible red laser diode, the entire laser system is classified as Class 3a.

The entire system is completely enclosed with a protective housing. This will completely contain the invisible C02 laser beam under normal use. However, the red diode laser is a visible laser beam. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL

INSTRUMENTS.

The user door(s) are safety interlocked and will disable the CO2 laser beam from firing when the user door(s) are opened. The control panel will also display a flashing “RED” light to visually indicate that the safety interlock system has been activated. The red diode laser beam is NOT safety interlocked and can be activated with the door(s) either open or closed.

Image 8
Contents Laser Platform Universal Laser Systems Inc All Rights Reserved Introduction Table of Contents Options & Accessories Sample MaterialsAppendices MaintenanceTroubleshooting General Safety Description of Appropriate UseLaser Safety SafetySafety Labels AB C DOr D UL-30 FCC Compliance FCC Compliance Statement and WarningsEU Compliance CE EU Declaration of ConformityInstallation Operating EnvironmentInstallation Electrical RequirementsExhaust Requirements Gate Cart Assembly Installation Laser Cartridge Installation Installation Laser Cooling Requirements Computer RequirementsSoftware Suggestions Graphics ProgramsFont Requirements Making the Connections Problem Prevention Computer Controlling the Laser SystemControl Panel DC Power SupplyHow it Works Laser Cartridge System Operation Laser CartridgeMotion System Control PanelSystem Operation System Operation Liquid Crystal Display LCD Process Controls System Operation Green Indicator LightRed Indicator Light Motion Control System Menu System System Operation Menu Descriptions Ready MenuSystem Operation File Display Menu Main Menu Memory Control MenuSystem Operation System Operation DOS Power Settings Menu Preferences MenuSystem Operation Options Menu ONE File Memory MenuHelpful Hint Autofocus MenuConfiguration Menu System Operation AIR Assist MenuDual Head Menu SET Focus Position MenuSET Rotary Axis Menu Tickle Menu Ports MenuLanguage Menu Units MenuSystem Operation Diagnostics Menu Alignment Mode MenuMemory Test Menu Motor Status DisplayAbout Menu Focusing the Laser Beam Focus Tool Method SET Focal Height Menu Material Thickness Z Position MethodCurrent Lens Menu System Operation Autofocus Method To Use AutofocusTo Adjust Autofocus Powering Up Loading and Positioning the MaterialFocusing Running the System Step by StepDownloading the File Setting the Drivers PropertiesCreating the Graphic Starting the Engraving Process Material Removing and Reloading Single Stamp Method 3D EffectsRubber Stamps Options & Accessories Place Stamp in AN Unused AreaOptions & Accessories Settings for a 30 Watt System Options & Accessories Full Sheet Method Rotary Fixture Cutting Table Air Assist System Air Assist CompressorFocus Lens Kits Focal Length Spot Size Focal Range Safety Sample MaterialsMaterials Sample MaterialsSample Materials Light Raster Engraving Comments Acrylic Mirrored Comments Raster Engraving Brass Painted Corian / Avonite / Fountainhead Cork Male Female Glass / Crystal Leather Marble MAT Board Melamine Standard Engraving Melamine PHOTO/CLIPART Engraving Plastic Engravers Microsurfaced Perforated Vector Cutting Vector Cutting Kiss CUT Wood Laser Engraving or Cutting Wood can Ignite the Material Maintenance Suggested Cleaning and Maintenance SuppliesMaintenance System Cleaning Optics CleaningMaintenance #2 Mirror Maintenance #3 Mirror and Focus Lens Maintenance Beam Window Autofocus Sensor and Reflector if installedAdjustments and Lubrication Fuse ReplacementBattery Replacement Electronic UpgradingMaintenance Schedule Cooling Fan FiltersTroubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Troubleshooting Ihr ULS Vertragshändler Operational Ihr ULS Vertragshändler Appendix Appendix a Limited Warranty Appendix B Specifications Facility RequirementsAppendix C Using DOS Based Programs Appendix D Using Macintosh Computers Appendix E Serial Port Cable Requirements Appendix F How To Get Help Step