Sears 113.241591 Blade TILT, or Squareness Blade to Table, Square and 45 Bevel Stop Screws

Page 12

9. Using a wood block and hammer as shown, move rear support bearing to right or left as req ui red to realign the blade. If necessary, shift front support bearing in similar manner; butdo NOT move front support bearing unless necessary, Recheck the

alignment with the square, then securely retighten all support bearing screws.

NOTE: Be certain that the widest blade you use does not contact blade insert after moving

support bearing. Check this at both 0° (perpendicular to the table) and 45 ° bevel by rotating the fully elevated blade by hand. Readjust as required to maintain sufficient clearance.

WOOD BLOCK

/

BLADE TILT, OR SQUARENESS OF

BLADE TO TABLE

90 ° (SQUARE) and 45 ° (BEVEL) STOP SCREWS.

When the bevel pointer is pointing directly to the "O" mark on the bevel scale, the sawblade should make a SQUARE cut 90° to the table.

To check for SQUARENESS:.

WARNING: TO AVOID INJURY FRONt

ACCIDENTAL START, TURN SWITCH "0 FF" AND

REMOVE PLUG FROM POWER SOURCE OUTLET,

1.Blade should be all'the way UP.

2.Place the square against blade. Make sure square is nottouching the TIP of one of the saw TEETH

O

"_J/__--TILT

CLAMP SCREW

-,,_"_"_TILT LOCK I'IAN[)LE

3. Turn the tilt-lock handle (COUNTER-- CLOCKWISE) to loosen the tilt clamp screw.

4.NOTE: Handle is spring loaded for engagement with screw head --must be pushed inward for disengagement whenever necessary to obtain a new grip on screw head.

// \

12

Image 12
Contents Model no Save This Manual For Future ReferenceFull ONE Year Warranty on Craftsman TAB LE SAW Know Your Power Tool Ground ALL ToolsKeep Work Area Clean Keep Guards in PlaceLocation Saw should be positioned so neitherKickbacks Protection EYES, HANDS, FACE, EARS, BodyUSE only Accessories Designed for this SAW Think SafetyOperation of any power tool can result in foreign Know Your Cutting ToolsConnecting to Power Source Outlet 200Unpacking and Checking Contents \i lList of Loose Parts QtyPart Name Qty ExternalWasher Wing Screw Washer Support RodAssembly Assembling Steel LegsMounting SAW Through the Holes in the Side Stiffeners MarkedInstalling Handwheels Important -- Read Before ProceedingChecking Table INS ERT Remove Plug from Power Source Outlet GrooveBlade TILT, or Squareness Blade to Table Square and 45 Bevel Stop ScrewsBlade should be allthe way UP \ \ TiLT Mechanism Mounting the MotorCheck Motor Rotation Diameter ShaftMounting the Flexible Shaft Conniector is puslted on the shaft as far as itShafthousing Small FerruleMotor Connector Hardware For Installing Extensions To SAW Table Attaching and Assembling Table ExtensionsLarge Ferrule No. Description QtyInstalling RiP Fence Guide Bars Mounting SwitchSELF-THREADING NUT Hole Aligning RIP Fence Increased Raise lock leverAdjusting RiP Scale iNDiCATOR INSTALLING Blade GuardLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Adjusting Miter Gauge AvordINJURY I / t TightlyagainstiAssembling HOLD-DOWN Plugging in MotorON-OFF Switch Getting to Know Your SAWSawblade Yellow PlasticTo Avoid Injury DUE to H OFF Power Ving Tilt, orROD Surface Pull towardRemoving and Installing Sawblade EXACT-I-CUTOperation Work HelpersPush Stick and Push Block Auxiliary FENCE/WORK SupportCrosscutting REPETiTiVE CuttingMiter Cutting Bevel CrosscuttingCompound Moter Cutting RiPPiNGBevel Ripping ReasonPage Ploughing and Molding INSTALL Blade Guard Immediately Upon ResawingCutting Panels RabbetingUsing Featherboards Always USE Dado Insert Listed Under Recommended AccessoriesDadoing LUBRICATmON and Maintenance Do not allow sawdust to accumulate inside SawRecommended Accessories Lubrication of Flexible ShaftCAT. no Outlet Before Troubleshooting TroubleRemedy Trouble Probable Cause RemedyRequest voltage check from the power Starting SwitchOr falls to come up CompanyRepair Parts IIC Page € u EcoooIndicator 62944 Key Part DescriptionHandle 62529 Shoe 62531Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no Key Part No. No60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64ON/OFF Power Outlet Does Not Include Key No Order Separately If RequiredParts List for Craftsman Deluxe 10 iNCH Table SAW Model no Guard AssemblyKey Pa Description 6031462552 STD551225Motor Key Part 60306Thread Service PartNumber Part Description Model Name