Sears 113.241591 Attaching and Assembling Table Extensions, Large Ferrule, No. Description Qty

Page 18

14.With end of LARGE FERRULE inserted into

recess in motor end cap tighten 2 Hex Head nuts on shaft brackets. LARGE FERRULE must be

pushed against the motor end ca p as far as it wil I go. Tighten nuts but do not OVERTIGHTEN. The shaft brackets hold the LARGE FERRULE in place. Nuts should be securely tightened to prevent movement. Overtightening may cause damage to the LARGE FERRULE.

IMPORTANT: The LARGE FERRULE should be centered over the MOTOR CONNECTOR (now located Inside of LARGE FERRULE), to prevent

the MOTOR CONNECTOR from contacting the

LARGE FERRULE.

15.Carefully turn saw blade by hand to make sure MOTOR CONNECTOR does not hit LARGE FERRULE.-If they are .in contact, it will cause a noise and cause resistance to rotation,

16.If the MOTOR CONNECTOR does hit the

LARGE FERRULE loosen the nuts holding the shaft brackets to the saw base, and the nuts

holding the LARGE FERRULE in the shaft brackets. Adjust the brackets and the LARGE FERRULE until the LARGE FERRULE is

centered and is not hit by the MOTOR CONNECTOR.

NOTE: It may be necessary to raise or lower

motor on motor mount slightly. Be sure to reposition shaft brackets as required.

17.Tighten nuts.

ATTACHING AND ASSEMBLING

TABLE EXTENSIONS

From among the loose parts find the following hardware: ((_uantity indicated is for 2 extensions)

HARDWARE	FOR INSTALLING
EXTENSIONS	TO SAW TABLE
Ref.
No. Description		Qty.

1Hex Hd. Screw, 5/16-18 x 1-1/4 .... .. 8

2	Flat Washer (Dia. of	Hole 11/32)	8
3	External Lockwasher,	5/16_	8

__BEAD ON FERRULE MUST

CONTACT MOTOR END CAP

	/	MOTOR
	z
	LARGE	CONNECTOR	BRACKETS	UP OR
	FERRULE	MOVE
		DOWN	SO THAT	MOTOR

CONNECTOR INSIDE DOES

NOT HIT FERRULE.

Image 18

Contents Model no Save This Manual For Future ReferenceKeep Work Area Clean Full ONE Year Warranty on Craftsman TAB LE SAWKnow Your Power Tool Ground ALL Tools Keep Guards in PlaceKickbacks LocationSaw should be positioned so neither Protection EYES, HANDS, FACE, EARS, BodyOperation of any power tool can result in foreign USE only Accessories Designed for this SAWThink Safety Know Your Cutting ToolsConnecting to Power Source Outlet 200Unpacking and Checking Contents \i lList of Loose Parts QtyWasher Part Name QtyExternal Wing Screw Washer Support RodMounting SAW AssemblyAssembling Steel Legs Through the Holes in the Side Stiffeners MarkedInstalling Handwheels Important -- Read Before ProceedingChecking Table INS ERT Remove Plug from Power Source Outlet GrooveBlade TILT, or Squareness Blade to Table Square and 45 Bevel Stop ScrewsBlade should be allthe way UP \ \ Check Motor Rotation TiLT MechanismMounting the Motor Diameter ShaftMounting the Flexible Shaft Conniector is puslted on the shaft as far as itShafthousing Small FerruleMotor Connector Large Ferrule Hardware For Installing Extensions To SAW TableAttaching and Assembling Table Extensions No. Description QtyInstalling RiP Fence Guide Bars Mounting SwitchSELF-THREADING NUT Hole Aligning RIP Fence Increased Raise lock leverLockwashers 1/4 in. External Type approx, die. of hole 1/4 Adjusting RiP Scale iNDiCATORINSTALLING Blade Guard Plate Nut Spreader Clamp Spreader BracketRip fence guide bar INJURY Adjusting Miter GaugeAvord I / t TightlyagainstiAssembling HOLD-DOWN Plugging in MotorSawblade ON-OFF SwitchGetting to Know Your SAW Yellow PlasticROD To Avoid Injury DUE to H OFF Power VingTilt, or Surface Pull towardRemoving and Installing Sawblade EXACT-I-CUTPush Stick and Push Block OperationWork Helpers Auxiliary FENCE/WORK SupportCrosscutting REPETiTiVE CuttingMiter Cutting Bevel CrosscuttingBevel Ripping Compound Moter CuttingRiPPiNG ReasonPage Ploughing and Molding Cutting Panels INSTALL Blade Guard Immediately UponResawing RabbetingUsing Featherboards Always USE Dado Insert Listed Under Recommended AccessoriesDadoing LUBRICATmON and Maintenance Do not allow sawdust to accumulate inside SawRecommended Accessories Lubrication of Flexible ShaftCAT. no Remedy Outlet Before TroubleshootingTrouble Trouble Probable Cause RemedyOr falls to come up Request voltage check from the powerStarting Switch CompanyRepair Parts IIC Page € u EcoooHandle 62529 Indicator 62944Key Part Description Shoe 6253160425 62779 62778 62777 STD541231 62482 37858 Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model noKey Part No. No Washer, 21/64ON/OFF Power Outlet Does Not Include Key No Order Separately If RequiredParts List for Craftsman Deluxe 10 iNCH Table SAW Model no Guard Assembly62552 Key PaDescription 60314 STD551225Motor Key Part 60306Thread Service PartNumber Part Description Model Name