Sears 113.241591 owner manual Motor Connector

Page 17

9.Bend the SHAFT HOUSING toward the motor as illustrated, insert end of LARGE FERRULE

over MOTOR CONNECTOR and line up

SQUARE END of flexible shaft with square hoJe in MOTOR CONNECTOR.

NOTF.: ff FLEXIBLE SHAFT is not properly positioned in the square hole of the MOTOR CONNECTOR it will not be Possible to make this con nection. It may be necessary to carefully rotate the blade to line up the SQUARE END of

the flexible shaft with the square hole in the

MOTOR CONNECTOR.

10.Push LARGE FERRULE as far as it will go against the motor end cap. if it does not enter motor end cap to ferrule bead, rotate saw blade while pushing ferrule toward motorto permitthe square ends of the core to enter their square mating holes deep enough to allow ferrule to be correctly positioned.

11.Assemble upper and lower shaft bracket by inserting 1/4-20 x 3/4 carriage bolts in upper and lower square holes on the saw base rear panel and then through the slotted hole in the shaft brackets. AssembJe 17/64 x 3/4 x 1/16 washer, External Type Lockwasher, and 1/4-20 Hex Nut. Finger tighten.

12.POsition the upper and lower shaft brackets so they wrap around the LARGE FERRULE on the SHAFT HOUSING. Bottom bracket should just

contact and support LARG E FERRULE. Tighten nuts that hold the shaft b rackets to the saw base.

13.Assemble two 1/4-20 x 1 in. Hex Head Screws, External Lockwashers, and !/4-20 Hex Nuts to clamp upper and lower brackets together. Do. not tighten.

CAREFULLY ROTATE BLADE BY HAND TO LINE UP SQUARE

END OF FLEXIBLE SHAFT

WiTH SQUARE HOLE IN

MOTOR CONNECTOR

\

17

Image 17
Contents Save This Manual For Future Reference Model noKnow Your Power Tool Ground ALL Tools Full ONE Year Warranty on Craftsman TAB LE SAWKeep Work Area Clean Keep Guards in PlaceSaw should be positioned so neither LocationKickbacks Protection EYES, HANDS, FACE, EARS, BodyThink Safety USE only Accessories Designed for this SAWOperation of any power tool can result in foreign Know Your Cutting Tools200 Connecting to Power Source Outlet\i l Unpacking and Checking ContentsQty List of Loose PartsExternal Part Name QtyWasher Wing Screw Washer Support RodAssembling Steel Legs AssemblyMounting SAW Through the Holes in the Side Stiffeners MarkedChecking Table INS ERT Installing HandwheelsImportant -- Read Before Proceeding Groove Remove Plug from Power Source OutletBlade should be allthe way UP Blade TILT, or Squareness Blade to TableSquare and 45 Bevel Stop Screws \ \ Mounting the Motor TiLT MechanismCheck Motor Rotation Diameter ShaftConniector is puslted on the shaft as far as it Mounting the Flexible ShaftSmall Ferrule ShafthousingMotor Connector Attaching and Assembling Table Extensions Hardware For Installing Extensions To SAW TableLarge Ferrule No. Description QtyMounting Switch Installing RiP Fence Guide BarsSELF-THREADING NUT Hole Aligning RIP Fence Raise lock lever IncreasedINSTALLING Blade Guard Adjusting RiP Scale iNDiCATORLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Avord Adjusting Miter GaugeINJURY I / t TightlyagainstiPlugging in Motor Assembling HOLD-DOWNGetting to Know Your SAW ON-OFF SwitchSawblade Yellow PlasticTilt, or To Avoid Injury DUE to H OFF Power VingROD Surface Pull towardEXACT-I-CUT Removing and Installing SawbladeWork Helpers OperationPush Stick and Push Block Auxiliary FENCE/WORK SupportREPETiTiVE Cutting CrosscuttingBevel Crosscutting Miter CuttingRiPPiNG Compound Moter CuttingBevel Ripping ReasonPage Ploughing and Molding Resawing INSTALL Blade Guard Immediately UponCutting Panels RabbetingDadoing Using FeatherboardsAlways USE Dado Insert Listed Under Recommended Accessories Do not allow sawdust to accumulate inside Saw LUBRICATmON and MaintenanceCAT. no Recommended AccessoriesLubrication of Flexible Shaft Trouble Outlet Before TroubleshootingRemedy Trouble Probable Cause RemedyStarting Switch Request voltage check from the powerOr falls to come up CompanyRepair Parts IIC Page Ecooo € uKey Part Description Indicator 62944Handle 62529 Shoe 62531Key Part No. No Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64Does Not Include Key No Order Separately If Required ON/OFF Power OutletGuard Assembly Parts List for Craftsman Deluxe 10 iNCH Table SAW Model noDescription 60314 Key Pa62552 STD551225Thread Motor Key Part60306 Number Part Description Model Name ServicePart