Sears 113.241591 owner manual Dadoing, Using Featherboards

Page 37

DADOING

Instructions for operating the Dado Head are contained in boo _let furnished with the Dado Head.

The Recommended Dado Head is listed under Recommended Accessories in this manual.

The arbor on the saw, is only long enough so that the widest cut that can be made is 13/16" wide.

It is not necessary to install the outside loose collar before screwing on the arbor nut. Make sure the arbor nut is tig ht.

ALWAYS USE DADO INSERT LISTED UNDER RECOMMENDED ACCESSORIES.

When using the dado head it will be necessary to remove the Blade Guard and Spreader. Use Miter

Gage and follow same procedures ano Instructions for C ross Cutting.

ALWAYS REPLACE THE BLADE, GUARD AND

SPREADER WHEN YOU ARE FINISHED DADOING.

MOLDING CUTTING

Instructions for operating the Molding Head are

oo

LOOSE :OLLA_

ARBOR _

SAW ARBOR

REMOVE SAWBLADE AND

contained in a booklet furnished with the Molding Head.

.J

INSTALL DADO HEAD

BACK OF SAW

The recommended molding head is listed under Recommended Accessories in this manual

Always use Molding Insert Listed Under

Recommended Accessories.

When using the molding head it will be necessaryto remove the Blade Guard and Spreader. USE

CAUTION. USE FEATHERBOARDS AND PUSH STICKS, etc AS REQUIRED.

ALWAYS REPLACE THE BLADE GUARD AND

SPREADER WHEN YOU ARE FINISHED MOLDING.

USING FEATHERBOARDS

Add 8 inch high flat facing board to the fence, the full length of the fence.

Use featherboar.ds for all non "thru-sawing"

operations (when sawblade guard must be removed). Featherboards are used to keep the work in contact with the fence and table as shown, and to stop kickbacks.

Mount featherboards to fence and table as shown, so that leading edges of featherboards will support workpiece until cut is complete, and the workpiece has been pushed completely past the cutter

(sawblade, dado head molding head, etc.) with a pushstick, as in ripping.

"C" CLAMPS

FEATHERBOARD

WORK SUPPORT

Before starting the operation (switch "OFF" and cutter below table surface):

(a)Install featherboards so they exert pressure on the work piece; be positive they are secure, and

(b)Make sure by trial that the featherboards will stop a kickback if one should occur.

Featherboards are not employed during non thru- sawing operations when using the miter gauge.

Replace the sawblade guard as soon as the non thru-sawing ooeration is complete.

/

37

Image 37

Contents Save This Manual For Future Reference Model noKnow Your Power Tool Ground ALL Tools Full ONE Year Warranty on Craftsman TAB LE SAWKeep Work Area Clean Keep Guards in PlaceSaw should be positioned so neither LocationKickbacks Protection EYES, HANDS, FACE, EARS, BodyThink Safety USE only Accessories Designed for this SAWOperation of any power tool can result in foreign Know Your Cutting Tools200 Connecting to Power Source Outlet\i l Unpacking and Checking ContentsQty List of Loose PartsExternal Part Name QtyWasher Wing Screw Washer Support RodAssembling Steel Legs AssemblyMounting SAW Through the Holes in the Side Stiffeners MarkedImportant -- Read Before Proceeding Installing HandwheelsChecking Table INS ERT Groove Remove Plug from Power Source OutletSquare and 45 Bevel Stop Screws Blade TILT, or Squareness Blade to TableBlade should be allthe way UP \ \ Mounting the Motor TiLT MechanismCheck Motor Rotation Diameter ShaftConniector is puslted on the shaft as far as it Mounting the Flexible ShaftSmall Ferrule ShafthousingMotor Connector Attaching and Assembling Table Extensions Hardware For Installing Extensions To SAW TableLarge Ferrule No. Description QtyMounting Switch Installing RiP Fence Guide BarsSELF-THREADING NUT Hole Aligning RIP Fence Raise lock lever IncreasedINSTALLING Blade Guard Adjusting RiP Scale iNDiCATORLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Avord Adjusting Miter GaugeINJURY I / t TightlyagainstiPlugging in Motor Assembling HOLD-DOWNGetting to Know Your SAW ON-OFF SwitchSawblade Yellow PlasticTilt, or To Avoid Injury DUE to H OFF Power VingROD Surface Pull towardEXACT-I-CUT Removing and Installing SawbladeWork Helpers OperationPush Stick and Push Block Auxiliary FENCE/WORK SupportREPETiTiVE Cutting CrosscuttingBevel Crosscutting Miter CuttingRiPPiNG Compound Moter CuttingBevel Ripping ReasonPage Ploughing and Molding Resawing INSTALL Blade Guard Immediately UponCutting Panels RabbetingAlways USE Dado Insert Listed Under Recommended Accessories Using FeatherboardsDadoing Do not allow sawdust to accumulate inside Saw LUBRICATmON and MaintenanceLubrication of Flexible Shaft Recommended AccessoriesCAT. no Trouble Outlet Before TroubleshootingRemedy Trouble Probable Cause RemedyStarting Switch Request voltage check from the powerOr falls to come up CompanyRepair Parts IIC Page Ecooo € uKey Part Description Indicator 62944Handle 62529 Shoe 62531Key Part No. No Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64Does Not Include Key No Order Separately If Required ON/OFF Power OutletGuard Assembly Parts List for Craftsman Deluxe 10 iNCH Table SAW Model noDescription 60314 Key Pa62552 STD55122560306 Motor Key PartThread Part ServiceNumber Part Description Model Name