Sears 113.241591 TiLT Mechanism, Mounting the Motor, Check Motor Rotation, Diameter Shaft

Page 14

TiLT MECHANISM

Lower blade to 2 inches or closer to the table top before tilting blade. Failure to do this may result in damage to your saw.

The handwheel should turn freely without binding. The turn ing action can be adjusted by tightening or loosening the screws in the bearing retainer.

NOTE: Tilt Handwheel must be removed to adjust. When adjusting the screws in the bearing retainer

using a screwdriver, hold the nut inside using a 3/8 in. wrench.

TILT HANDWHEEL

_J

ADJUST THESE

TWO SCREWS

MOUNTING THE MOTOR

1.CHECK MOTOR ROTATION

A.The motor must rotate COUNTER-- CLOCKWISE when viewed from the shaft end.

B.MAKE SURE "'KEY" IS REMOVED FROM SHAFT,

C.Place the motor on your workbench or on the floor.

D.Plug the cord into a properly grounded outlet

(See "Motor Specifications and Electrical Requirements" Section.) Notice the rotation

of the shaft. If it is not turning

COUNTERCLOCKWISE, do not continue assembly, Contact your nearest Sears Store or Service Center.

E.Remove plug from outlet.

DIAMETER SHAFT

5/8 INCH

(f

_,._

_"_" KEY

COUNTER-CLOCKWISE

ROTATION

14

Image 14

Contents Model no Save This Manual For Future ReferenceKeep Work Area Clean Full ONE Year Warranty on Craftsman TAB LE SAWKnow Your Power Tool Ground ALL Tools Keep Guards in PlaceKickbacks LocationSaw should be positioned so neither Protection EYES, HANDS, FACE, EARS, BodyOperation of any power tool can result in foreign USE only Accessories Designed for this SAWThink Safety Know Your Cutting ToolsConnecting to Power Source Outlet 200Unpacking and Checking Contents \i lList of Loose Parts QtyWasher Part Name QtyExternal Wing Screw Washer Support RodMounting SAW AssemblyAssembling Steel Legs Through the Holes in the Side Stiffeners MarkedChecking Table INS ERT Installing HandwheelsImportant -- Read Before Proceeding Remove Plug from Power Source Outlet GrooveBlade should be allthe way UP Blade TILT, or Squareness Blade to TableSquare and 45 Bevel Stop Screws \ \ Check Motor Rotation TiLT MechanismMounting the Motor Diameter ShaftMounting the Flexible Shaft Conniector is puslted on the shaft as far as itShafthousing Small FerruleMotor Connector Large Ferrule Hardware For Installing Extensions To SAW TableAttaching and Assembling Table Extensions No. Description QtyInstalling RiP Fence Guide Bars Mounting SwitchSELF-THREADING NUT Hole Aligning RIP Fence Increased Raise lock leverLockwashers 1/4 in. External Type approx, die. of hole 1/4 Adjusting RiP Scale iNDiCATORINSTALLING Blade Guard Plate Nut Spreader Clamp Spreader BracketRip fence guide bar INJURY Adjusting Miter GaugeAvord I / t TightlyagainstiAssembling HOLD-DOWN Plugging in MotorSawblade ON-OFF SwitchGetting to Know Your SAW Yellow PlasticROD To Avoid Injury DUE to H OFF Power VingTilt, or Surface Pull towardRemoving and Installing Sawblade EXACT-I-CUTPush Stick and Push Block OperationWork Helpers Auxiliary FENCE/WORK SupportCrosscutting REPETiTiVE CuttingMiter Cutting Bevel CrosscuttingBevel Ripping Compound Moter CuttingRiPPiNG ReasonPage Ploughing and Molding Cutting Panels INSTALL Blade Guard Immediately UponResawing RabbetingDadoing Using FeatherboardsAlways USE Dado Insert Listed Under Recommended Accessories LUBRICATmON and Maintenance Do not allow sawdust to accumulate inside SawCAT. no Recommended AccessoriesLubrication of Flexible Shaft Remedy Outlet Before TroubleshootingTrouble Trouble Probable Cause RemedyOr falls to come up Request voltage check from the powerStarting Switch CompanyRepair Parts IIC Page € u EcoooHandle 62529 Indicator 62944Key Part Description Shoe 6253160425 62779 62778 62777 STD541231 62482 37858 Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model noKey Part No. No Washer, 21/64ON/OFF Power Outlet Does Not Include Key No Order Separately If RequiredParts List for Craftsman Deluxe 10 iNCH Table SAW Model no Guard Assembly62552 Key PaDescription 60314 STD551225Thread Motor Key Part60306 Number Part Description Model Name ServicePart