Sears 113.241591 owner manual Shafthousing, Small Ferrule

Page 16

5.Removetheplasticcoversfromtheendsof the

SHAFTHOUSING.

6.Push the saw arbor end of the flexible shaft out

of the SHAFT HOUSING until it is

approximately 1 inch above the end of the

SMALL FERRULE.

SAW ARBOR

MOTOR END d

_ --.

END

PULL	FLEXIBLE	SAW ARBOR END
SHAFT	OUT	1"

7.Insert the flexible shaft assembly through the opening in the side of the saw base. Line up the SQUARE END of the FLEXIBLE SHAFTwith the

square hole in the arbor shaft, holding square end of flexible shaft insert the FLEXIBLE SHA F]- into the square hole in the arbor as far as it wil I go.

IMPORTANT: Make sure the FLEXIBLE SHAFT is

inserted as far as it will go. Approximately 3/4 inch.

©

L_[

O

SHAFT RETAINER

PAN HEAD SCREW 10-32 x 3/8 iN.

6

Image 16

Contents Model no Save This Manual For Future ReferenceFull ONE Year Warranty on Craftsman TAB LE SAW Know Your Power Tool Ground ALL ToolsKeep Work Area Clean Keep Guards in PlaceLocation Saw should be positioned so neitherKickbacks Protection EYES, HANDS, FACE, EARS, BodyUSE only Accessories Designed for this SAW Think SafetyOperation of any power tool can result in foreign Know Your Cutting ToolsConnecting to Power Source Outlet 200Unpacking and Checking Contents \i lList of Loose Parts QtyPart Name Qty ExternalWasher Wing Screw Washer Support RodAssembly Assembling Steel LegsMounting SAW Through the Holes in the Side Stiffeners MarkedImportant -- Read Before Proceeding Installing HandwheelsChecking Table INS ERT Remove Plug from Power Source Outlet GrooveSquare and 45 Bevel Stop Screws Blade TILT, or Squareness Blade to TableBlade should be allthe way UP \ \ TiLT Mechanism Mounting the MotorCheck Motor Rotation Diameter ShaftMounting the Flexible Shaft Conniector is puslted on the shaft as far as itShafthousing Small FerruleMotor Connector Hardware For Installing Extensions To SAW Table Attaching and Assembling Table ExtensionsLarge Ferrule No. Description QtyInstalling RiP Fence Guide Bars Mounting SwitchSELF-THREADING NUT Hole Aligning RIP Fence Increased Raise lock leverAdjusting RiP Scale iNDiCATOR INSTALLING Blade GuardLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Adjusting Miter Gauge AvordINJURY I / t TightlyagainstiAssembling HOLD-DOWN Plugging in MotorON-OFF Switch Getting to Know Your SAWSawblade Yellow PlasticTo Avoid Injury DUE to H OFF Power Ving Tilt, orROD Surface Pull towardRemoving and Installing Sawblade EXACT-I-CUTOperation Work HelpersPush Stick and Push Block Auxiliary FENCE/WORK SupportCrosscutting REPETiTiVE CuttingMiter Cutting Bevel CrosscuttingCompound Moter Cutting RiPPiNGBevel Ripping ReasonPage Ploughing and Molding INSTALL Blade Guard Immediately Upon ResawingCutting Panels RabbetingAlways USE Dado Insert Listed Under Recommended Accessories Using FeatherboardsDadoing LUBRICATmON and Maintenance Do not allow sawdust to accumulate inside SawLubrication of Flexible Shaft Recommended AccessoriesCAT. no Outlet Before Troubleshooting TroubleRemedy Trouble Probable Cause RemedyRequest voltage check from the power Starting SwitchOr falls to come up CompanyRepair Parts IIC Page € u EcoooIndicator 62944 Key Part DescriptionHandle 62529 Shoe 62531Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no Key Part No. No60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64ON/OFF Power Outlet Does Not Include Key No Order Separately If RequiredParts List for Craftsman Deluxe 10 iNCH Table SAW Model no Guard AssemblyKey Pa Description 6031462552 STD55122560306 Motor Key PartThread Part ServiceNumber Part Description Model Name