Sears 113.241591 owner manual Ploughing and Molding

Page 35

Feed the workpie'ce by hand along the AUXILIARY FENCE until the end is approx. 1 in. past the front edge of the table. Continue to feed using the PUSH BLOCK.

Hold the workpiece in position and install the PUSH

BLOCK by sliding it on top of the AUXILIARY

FENCE/WORK SUPPORT (This May Raise Guard)-

BAFFLE

Narrow strips thicker than the Auxiliary Fence/Work Support may enter the guard and strike the baffle. CAREFULLY raise guard only enough to clear the workpiece. Use PUSH BLOCK to complete cut.

PLOUGHING AND MOLDING

PLOUGHING is grooving with the grain the long way of the workpiece, using the fence. USE Featherboards and push sticks as required.

MOLDING is shaping the workpiece with the grair

the long way of the workpiece, using the fence. USE Featherboards and push sticks as required.

PLOUGHIN

MOLDING

Image 35

Contents Save This Manual For Future Reference Model noKeep Guards in Place Full ONE Year Warranty on Craftsman TAB LE SAWKnow Your Power Tool Ground ALL Tools Keep Work Area CleanProtection EYES, HANDS, FACE, EARS, Body LocationSaw should be positioned so neither KickbacksKnow Your Cutting Tools USE only Accessories Designed for this SAWThink Safety Operation of any power tool can result in foreign200 Connecting to Power Source Outlet\i l Unpacking and Checking ContentsQty List of Loose PartsWing Screw Washer Support Rod Part Name QtyExternal WasherThrough the Holes in the Side Stiffeners Marked AssemblyAssembling Steel Legs Mounting SAWChecking Table INS ERT Installing HandwheelsImportant -- Read Before Proceeding Groove Remove Plug from Power Source OutletBlade should be allthe way UP Blade TILT, or Squareness Blade to TableSquare and 45 Bevel Stop Screws \ \ Diameter Shaft TiLT MechanismMounting the Motor Check Motor RotationConniector is puslted on the shaft as far as it Mounting the Flexible ShaftSmall Ferrule ShafthousingMotor Connector No. Description Qty Hardware For Installing Extensions To SAW TableAttaching and Assembling Table Extensions Large FerruleMounting Switch Installing RiP Fence Guide BarsSELF-THREADING NUT Hole Aligning RIP Fence Raise lock lever IncreasedPlate Nut Spreader Clamp Spreader Bracket Adjusting RiP Scale iNDiCATORINSTALLING Blade Guard Lockwashers 1/4 in. External Type approx, die. of hole 1/4Rip fence guide bar I / t Tightlyagainsti Adjusting Miter GaugeAvord INJURYPlugging in Motor Assembling HOLD-DOWNYellow Plastic ON-OFF SwitchGetting to Know Your SAW SawbladeSurface Pull toward To Avoid Injury DUE to H OFF Power VingTilt, or RODEXACT-I-CUT Removing and Installing SawbladeAuxiliary FENCE/WORK Support OperationWork Helpers Push Stick and Push BlockREPETiTiVE Cutting CrosscuttingBevel Crosscutting Miter CuttingReason Compound Moter CuttingRiPPiNG Bevel RippingPage Ploughing and Molding Rabbeting INSTALL Blade Guard Immediately UponResawing Cutting PanelsDadoing Using FeatherboardsAlways USE Dado Insert Listed Under Recommended Accessories Do not allow sawdust to accumulate inside Saw LUBRICATmON and MaintenanceCAT. no Recommended AccessoriesLubrication of Flexible Shaft Trouble Probable Cause Remedy Outlet Before TroubleshootingTrouble RemedyCompany Request voltage check from the powerStarting Switch Or falls to come upRepair Parts IIC Page Ecooo € uShoe 62531 Indicator 62944Key Part Description Handle 62529Washer, 21/64 Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model noKey Part No. No 60425 62779 62778 62777 STD541231 62482 37858Does Not Include Key No Order Separately If Required ON/OFF Power OutletGuard Assembly Parts List for Craftsman Deluxe 10 iNCH Table SAW Model noSTD551225 Key PaDescription 60314 62552Thread Motor Key Part60306 Number Part Description Model Name ServicePart