Sears 113.241591 owner manual Rip fence guide bar

Page 24

WARNING: TO AVOID INJURY DUE TO

ACCIDENTAL START, TURN SWITCH "OFF" AND

REMOVE PLUG FROM POWER SOURCE OUTLET.

2.MAKE SURE THE BLADE IS ALL THE WAY UP AND SQUARE WITH THE TABLE.

3.Position SPREADER SUPPORT on rod behind

the rip fence guide bar,

BLADE SQUARE

WITH TABLE

RIP FENCE

GUIDE BAR

SPREADER SUPPORT

POSITIONED ON ROD

BEHIND RIP FENCE

GUIDE BAR

4. Assemble the 7/8 in. long setscrews, nuts. \

Iockwashers and washers to the SPREADER \

SUPPORT BRACKET and slip the nuts into the slot in the spreader support.

5, Locate spreader support and bracket on rod. 1/16 inch behind the fence guide bar.

6, Finger tighten ONLY THE HEX NUTS.

SPREADER SUPPORT

..._-_-_BRACKET

VIEW LOOKING DOWN

FROM TOP

7.Lay a piece of flat straight wood and a square on saw table and rotatethe SPREADER SUPPORT until the bracket is aligned with square.

Image 24

Contents Model no Save This Manual For Future ReferenceFull ONE Year Warranty on Craftsman TAB LE SAW Know Your Power Tool Ground ALL ToolsKeep Work Area Clean Keep Guards in PlaceLocation Saw should be positioned so neitherKickbacks Protection EYES, HANDS, FACE, EARS, BodyUSE only Accessories Designed for this SAW Think SafetyOperation of any power tool can result in foreign Know Your Cutting ToolsConnecting to Power Source Outlet 200Unpacking and Checking Contents \i lList of Loose Parts QtyPart Name Qty ExternalWasher Wing Screw Washer Support RodAssembly Assembling Steel LegsMounting SAW Through the Holes in the Side Stiffeners MarkedInstalling Handwheels Important -- Read Before ProceedingChecking Table INS ERT Remove Plug from Power Source Outlet GrooveBlade TILT, or Squareness Blade to Table Square and 45 Bevel Stop ScrewsBlade should be allthe way UP \ \ TiLT Mechanism Mounting the MotorCheck Motor Rotation Diameter ShaftMounting the Flexible Shaft Conniector is puslted on the shaft as far as itShafthousing Small FerruleMotor Connector Hardware For Installing Extensions To SAW Table Attaching and Assembling Table ExtensionsLarge Ferrule No. Description QtyInstalling RiP Fence Guide Bars Mounting SwitchSELF-THREADING NUT Hole Aligning RIP Fence Increased Raise lock leverAdjusting RiP Scale iNDiCATOR INSTALLING Blade GuardLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Adjusting Miter Gauge AvordINJURY I / t TightlyagainstiAssembling HOLD-DOWN Plugging in MotorON-OFF Switch Getting to Know Your SAWSawblade Yellow PlasticTo Avoid Injury DUE to H OFF Power Ving Tilt, orROD Surface Pull towardRemoving and Installing Sawblade EXACT-I-CUTOperation Work HelpersPush Stick and Push Block Auxiliary FENCE/WORK SupportCrosscutting REPETiTiVE CuttingMiter Cutting Bevel CrosscuttingCompound Moter Cutting RiPPiNGBevel Ripping ReasonPage Ploughing and Molding INSTALL Blade Guard Immediately Upon ResawingCutting Panels RabbetingUsing Featherboards Always USE Dado Insert Listed Under Recommended AccessoriesDadoing LUBRICATmON and Maintenance Do not allow sawdust to accumulate inside SawRecommended Accessories Lubrication of Flexible ShaftCAT. no Outlet Before Troubleshooting TroubleRemedy Trouble Probable Cause RemedyRequest voltage check from the power Starting SwitchOr falls to come up CompanyRepair Parts IIC Page € u EcoooIndicator 62944 Key Part DescriptionHandle 62529 Shoe 62531Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no Key Part No. No60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64ON/OFF Power Outlet Does Not Include Key No Order Separately If RequiredParts List for Craftsman Deluxe 10 iNCH Table SAW Model no Guard AssemblyKey Pa Description 6031462552 STD551225Motor Key Part 60306Thread Service PartNumber Part Description Model Name