Sears 113.241591 owner manual Getting to Know Your SAW, Sawblade, ON-OFF Switch, Yellow Plastic

Page 27

GETTING TO KNOW YOUR SAW

			9 SAWBLADE
		8 TABLE	INSERT
MITER	GAUGE	10 EXACT-I-CUT	ANTIKICKBACK
LOCK	HANDLE		PAWLS

RIP FENCE

HOLES FOR

ATTACHING FACING

6 MITER GAUGE

,,UNOTI TLOOK..EAT,,ABLE,.A"O

2 ELEVATION HANDWHEEL

1 ON-OFF SWITCH

1 ON-OFF SWITCH

CAUTION: Before turning switch on, make sure the blade guard is correctly installed and operating properly.

The On-Off Switch has a locking feature. THIS

FEATURE IS INTENDED TO PREVENT UNAUTHORIZED AND POSSIBLE HAZARDOUS USE BY CHILDREN AND OTHERS.

A. TO turn saw ON... stand to either side of the blade never in line with it . . . insert finger under switch lever and pull END of lever out.

Do not cycle the motor switch on and off rapidly, as this may cause the sawblade to loosen. In the event this should ever occur. allow the sawblade to come to a cornplete

stop and retighten the arbor nut normally, not excessively. Never leave the saw while the

power is "ON".

B. TO turn saw OFF. . PUSH lever in. Never leave the saw until the cutting tool has come

to a complete stop,

C. TO lock switch in OFF position.., hold switch IN with one hand... REMOVE key with other hand,

WARNING: FOR YOUR OWN SAFETY, LOWER BLADE OR OTHER CUTTING TOOL BELOW TABLE SU RFACE. (IF BLADE IS TILTED, RETURN IT TO VERTICAL (90 ° )

POSITION). ALWAYS LOCK THE SWITCH

OFF. WHEN SAW IS NOT IN USE.. • REMOVE KEY AND KEEP IT IN A SAFE PLACE . . . ALSO . .. IN THE EVENT OF A POWER FAILURE (ALL OF YOUR LIGHTS

GO OUT) TURN SWITCH OFF ... LOCK IT AND REMOVE THE KEY. THIS WILL

PREVENT THE SAW FROM STARTING UP

AGAIN WHEN THE POWER COMES BACK ON.

\

3 TILT HANDWHEEL

KEY

(YELLOW PLASTIC)

27

Image 27

Contents Save This Manual For Future Reference Model noKeep Guards in Place Full ONE Year Warranty on Craftsman TAB LE SAWKnow Your Power Tool Ground ALL Tools Keep Work Area CleanProtection EYES, HANDS, FACE, EARS, Body LocationSaw should be positioned so neither KickbacksKnow Your Cutting Tools USE only Accessories Designed for this SAWThink Safety Operation of any power tool can result in foreign200 Connecting to Power Source Outlet\i l Unpacking and Checking ContentsQty List of Loose PartsWing Screw Washer Support Rod Part Name QtyExternal WasherThrough the Holes in the Side Stiffeners Marked AssemblyAssembling Steel Legs Mounting SAWInstalling Handwheels Important -- Read Before ProceedingChecking Table INS ERT Groove Remove Plug from Power Source OutletBlade TILT, or Squareness Blade to Table Square and 45 Bevel Stop ScrewsBlade should be allthe way UP \ \ Diameter Shaft TiLT MechanismMounting the Motor Check Motor RotationConniector is puslted on the shaft as far as it Mounting the Flexible ShaftSmall Ferrule ShafthousingMotor Connector No. Description Qty Hardware For Installing Extensions To SAW TableAttaching and Assembling Table Extensions Large FerruleMounting Switch Installing RiP Fence Guide BarsSELF-THREADING NUT Hole Aligning RIP Fence Raise lock lever IncreasedPlate Nut Spreader Clamp Spreader Bracket Adjusting RiP Scale iNDiCATORINSTALLING Blade Guard Lockwashers 1/4 in. External Type approx, die. of hole 1/4Rip fence guide bar I / t Tightlyagainsti Adjusting Miter GaugeAvord INJURYPlugging in Motor Assembling HOLD-DOWNYellow Plastic ON-OFF SwitchGetting to Know Your SAW SawbladeSurface Pull toward To Avoid Injury DUE to H OFF Power VingTilt, or RODEXACT-I-CUT Removing and Installing SawbladeAuxiliary FENCE/WORK Support OperationWork Helpers Push Stick and Push BlockREPETiTiVE Cutting CrosscuttingBevel Crosscutting Miter CuttingReason Compound Moter CuttingRiPPiNG Bevel RippingPage Ploughing and Molding Rabbeting INSTALL Blade Guard Immediately UponResawing Cutting PanelsUsing Featherboards Always USE Dado Insert Listed Under Recommended AccessoriesDadoing Do not allow sawdust to accumulate inside Saw LUBRICATmON and MaintenanceRecommended Accessories Lubrication of Flexible ShaftCAT. no Trouble Probable Cause Remedy Outlet Before TroubleshootingTrouble RemedyCompany Request voltage check from the powerStarting Switch Or falls to come upRepair Parts IIC Page Ecooo € uShoe 62531 Indicator 62944Key Part Description Handle 62529Washer, 21/64 Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model noKey Part No. No 60425 62779 62778 62777 STD541231 62482 37858Does Not Include Key No Order Separately If Required ON/OFF Power OutletGuard Assembly Parts List for Craftsman Deluxe 10 iNCH Table SAW Model noSTD551225 Key PaDescription 60314 62552Motor Key Part 60306Thread Service PartNumber Part Description Model Name