Sears 113.241591 owner manual Model no, Save This Manual For Future Reference

Page 1

Save This Manual For Future Reference

owners manual

MODEL NO.

113.241591

SAW WITH LEGS

TWO CAST IRON

TABLE EXTENSIONS

MOTOR AND

HOLD DOWN CLAMP

Serial

Number

Model and serial number may be found at the rear of the base.

You should record both model and serial number in a safe place for future use.

CAUTION:

READ ALL

INSTRUCTIONS

CAREFULLY

DELUXE IO-INCH

FLEX DRIVE TABLE SAW

. assembly

. operating

=repair parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.

PriP,_:ed _n U_

Part No. 62965

Image 1

Contents Save This Manual For Future Reference Model noKnow Your Power Tool Ground ALL Tools Full ONE Year Warranty on Craftsman TAB LE SAWKeep Work Area Clean Keep Guards in PlaceSaw should be positioned so neither LocationKickbacks Protection EYES, HANDS, FACE, EARS, BodyThink Safety USE only Accessories Designed for this SAWOperation of any power tool can result in foreign Know Your Cutting Tools200 Connecting to Power Source Outlet\i l Unpacking and Checking ContentsQty List of Loose PartsExternal Part Name QtyWasher Wing Screw Washer Support RodAssembling Steel Legs AssemblyMounting SAW Through the Holes in the Side Stiffeners MarkedImportant -- Read Before Proceeding Installing HandwheelsChecking Table INS ERT Groove Remove Plug from Power Source OutletSquare and 45 Bevel Stop Screws Blade TILT, or Squareness Blade to TableBlade should be allthe way UP \ \ Mounting the Motor TiLT MechanismCheck Motor Rotation Diameter ShaftConniector is puslted on the shaft as far as it Mounting the Flexible ShaftSmall Ferrule ShafthousingMotor Connector Attaching and Assembling Table Extensions Hardware For Installing Extensions To SAW TableLarge Ferrule No. Description QtyMounting Switch Installing RiP Fence Guide BarsSELF-THREADING NUT Hole Aligning RIP Fence Raise lock lever IncreasedINSTALLING Blade Guard Adjusting RiP Scale iNDiCATORLockwashers 1/4 in. External Type approx, die. of hole 1/4 Plate Nut Spreader Clamp Spreader BracketRip fence guide bar Avord Adjusting Miter GaugeINJURY I / t TightlyagainstiPlugging in Motor Assembling HOLD-DOWNGetting to Know Your SAW ON-OFF SwitchSawblade Yellow PlasticTilt, or To Avoid Injury DUE to H OFF Power VingROD Surface Pull towardEXACT-I-CUT Removing and Installing SawbladeWork Helpers OperationPush Stick and Push Block Auxiliary FENCE/WORK SupportREPETiTiVE Cutting CrosscuttingBevel Crosscutting Miter CuttingRiPPiNG Compound Moter CuttingBevel Ripping ReasonPage Ploughing and Molding Resawing INSTALL Blade Guard Immediately UponCutting Panels RabbetingAlways USE Dado Insert Listed Under Recommended Accessories Using FeatherboardsDadoing Do not allow sawdust to accumulate inside Saw LUBRICATmON and MaintenanceLubrication of Flexible Shaft Recommended AccessoriesCAT. no Trouble Outlet Before TroubleshootingRemedy Trouble Probable Cause RemedyStarting Switch Request voltage check from the powerOr falls to come up CompanyRepair Parts IIC Page Ecooo € uKey Part Description Indicator 62944Handle 62529 Shoe 62531Key Part No. No Parts LaST for Craftsman Deluxe 10 iNCH Table SAW Model no60425 62779 62778 62777 STD541231 62482 37858 Washer, 21/64Does Not Include Key No Order Separately If Required ON/OFF Power OutletGuard Assembly Parts List for Craftsman Deluxe 10 iNCH Table SAW Model noDescription 60314 Key Pa62552 STD55122560306 Motor Key PartThread Part ServiceNumber Part Description Model Name