Sears 113.298141 Assembly, Installing Handwheels, Checking Table Insert, 32 I N, Setscrewwrench

ItemPartNameQty.

ZHexNut, 5/16-18

	(approx. dia. of hole 5/16 in.)	9
Z	Hex Nut, 1t4-20
	(approx.dia. of hole 114in.)	2
AA	Lockwasher, 5/I 6 in. ExternalType
	(approx.die. of hole 5116in.)	11
AA	Lockwasher,1/4 in. ExternalType
	(approx.alia.of h ale 1/4 in.)	2
AA	LockwasherNo. 10 ExternalType
	(approx.dia. of hole3t16 in.)	1
AB	CarriageBolt, 5/16-18 x 3/4 in. long	4
AC	Rip FenceGuideBarSpacer	2
AD	Wire Tie	2
AE	Thumbscrew,5/1G-18 x 1 in. long	1
AF	Screw PanHd. 10-32 x 3/4	1
AG	Flat Washer(dia. of hole 21/64)	2
The followingpartsare includedwith Model 113.298031 and
113.298151.
A	Leg	4
8	SideStiffener	2
C	End Stiffener	2
D	Table Extension(113.298031)	2
	Table Extension(113.298151)	I
E	Motor	I
	Pkg.of Miscellaneousmall Parts,No. 62752 for Legs
	Consistingof the Following:
F	Hex HeadScrew5116-18 x 1-1/4in. long ....	4,
G	Lockwasher,1/4 in. ExternalType
	(approx.dia.of hole1/4 in.)	24
G	Lockwasher,5/16 in. ExternalType
	(epprox. dia. of hole 5/16 in.)	4
H	Hex Nut, 1/4-20
	(approx.dia. of hole 1/4 in.)	24
H	Hex Nut, 5/16-18
	(approx.dia. of hole5/16 in.)	4
H	Hex Nut, 1/2-13
	(approx.dia. of hole1]2 in.)	8
J	Flat Washer(dia. of hole, 11/32 in.)	8

A

		©
		G	H
		F
J	K	L
Item	Pert Name		Qty.
K	TrussHeadScrew, 1/4-20 x 5/8 in. long
L	(top of screwisrounded)		24
	Leveling Foot		4
	Pkg.of MiscellaneousSmall PartsNo. 62745 for
	Table Extensions(1 ea. for Model 113.298151,
	2 ea. for Model 113.298031)
	Consistingof the following:
F	Hex Hd, Screw,5/16-18 x I-1/4in. long		..... 4
G	Lockwasher,ExternalType
	(approx. dia. of hole 1/4 in.)		8
G	Lockwasher, ExternalType
	(approx.dia. of hale 5/16 in.)		4

HHex Nut, 1/4-20

	(approx.alia.of hole114in.)	8
H	Hex Nut, 5/16-18
	(approx.dia. of hole5/16 in.)	8

KTrussHeadScrew, 1/4-20 x 1 in. long

	(top of screwisrounded)	8
M	Corner _;tiffener Bracket	2
N	CornerSupportBracket	2

ASSEMBLY

Before mounting the saw on legs, a stand or a bench, the Table Insert and Blade Squareness must be checked at this

time.

INSTALLING HANDWHEELS

1.Line up FLAT SPOTS on shaft and hardwheel, push handwheel onto shaft. Install screw and Iockwasher to lock handwheel on shaft.

LOCKWASHER

/

	10-32	X	3/4 IN.
ELEVATION	PAN	HEAD	SCREW

HANDWHEEL

/

TILT HANDWHEEL

CHECKING TABLE INSERT

2.Insert should be flush with table top. Check as shown. Loosen flat head screw that holds insert and adjust the

four set screws as necessary. Tighten flat head screw. Do not tighten screw to the point where it deflects the insert.

\

TABLE INSERT

3/32 I N.

SETSCREWWRENCH