RESAWING
RESAWING is known as ripping a piece of wood through its thickness. Do not attempt to resaw BOWED or WARPED material. NOTE: To RESAW a piece of wider than
blade guard ... and use the AUXILIARY FENCE/WORK SUPPORT. (See "Work Helpers").
Clamp it to the table so that the workpiece wil SLIDE EASILY but not TILT or MOVE SIDEWAYS without BINDING between the two fences.
Do not clamp directly to the bottom edge of the table because the "swivel" of the clamp will not grip properly. Place a small block of wood between the bottom edge of the table and the "C" clamp.
SMALL BLOCK
OF WOOD
RESAWlNG BECAUSE THIS COULD CAUSE A KICKBACK.
WARNING: FOR YOUR OWN SAFETY ... | 2- | INSTALL | BLADE | GUARD IMMEDIATELY | UPON | |
1. DO NOT "'BACK UP" (REVERSE FEEDING) WHILE | ||||||
| COMPLETION | OF | THE RESAWlNG OPERATION. |
|
CUTTING PANELS
When cutting panels (whenever fence is positioned outside
of table surface), ALWAYS use the AUXILIARY
FENCE/WORK SUPPORT.
1.Unlock fence and raise rear end.
2.Position AUXILIARY FENCE/WORK SUPPORT as shown and attach it with two "'C'"clamps.
RABBETING
Rabbeting is known as cutting out a section of the corner of a piece of material, across an end oralong an edge.
To make a RABBET requires cuts which do not go all the
way through the material. Therefore the blade guard must be removed.
1.Remove blade guard.
2.For rabbeting along an edge (long way of workpiece) as
shown, add facing to rip fence (see 5. RIP FENCE, p.
21)approximately as high as the workpiece is wide. Adjust rip fence and blade to required dimensions: then
make first cut with board flat on table as any rip (type) cut: make second cut with workpiece on edge. Follow
all precautions, safety instructions, and operational
instructions as for ripping, or rip type operations, including feather boards and push stick, etc.
3.For rabbeting across an end, for workpieee 101/=" and
DADOING
Instructions for operating the Dado Head are contained in booklet furnished with the Dado Head.
The Recommended Dado Head is listed under
Recommended Accessories in this manual.
The arbor on the saw, is only long enough so that the widest cut that can be made is 13/16" wide.
It is not necessary to install the outside loose col ar before
screwing on the arbor nut. Make sure the arbor nut is tight.
ALWAYS USE DADO INSERT LISTED UNDER
RECOMMENDED ACCESSORIES.
When using .the dado head it will be necessary to remove
the Blade Guard and Spreader. USE CAUTION. USE
FEATHERBOARDS AND PUSH STICKS AS REQUIRED.
ALWAYS REPLACE THE BLADE, GUARD AND
SPREADER WHEN YOU ARE FINISHED DADOING.
narrower make the rabbet cut with the board flat on
operations, including feather boards and push stick, etc. the table using the miter gage fitted w_th a facing (per
"6. MITER GAUGE" on p.21). DO NOT use the rip fence.
4. INSTALL BLADE GUARD IMMEDIATELY UPON
COMPLETION OF RABBETING OPERATION.
Rabbet cuts can also be made using the dado head or molding head.
SAW TABLE
\
_R NUT
MOLDING CUTTING |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| When using | the molding | heat it will be necessary to remove | ||||||
Instructions | for operating the | Molding | Head | are contained | the Blade | Guard | and | Spreader. | USE | CAUTION. | USE | |||||
in a booklet | furnished | with | the | Molding | Head. | FEATHERBOARDS | AND | PUSH STICKS, | etc | AS | ||||||
The | recommended | molding | head | is | listed under | REQUIRED. |
|
|
|
|
|
|
|
| ||
Recommended | Accessories | m this manual. |
| ALWAYS | REPLACE | THE | BLADE | GUARD | AND | |||||||
Always | use | Molding | Insert | Listed Under | Recommended | SPREADER | WHEN | YOU | ARE | FINISHED | MOLDING. |
| ||||
Accessories. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 2a |
|
|
|
|
|
|
|
|