Sears 113.298141 owner manual Attaching and Assembling Table Extensions, Tighten

Page 9

MOUNTINGSAW

1.From among the loose parts, find the following hardware:

4 Hex Head Screws. 5/16 - 18 x 1-1/4 in. long.

4 Hex Nuts, 5/16- 18 (approx. dia. of hole 5/16 in.)

4 Lockwashers, 5/16 in. External Type (approx. dia. of hole, 5/16 in.)

8 Flat Washers, (dia. of hole 11/32 in.)

2.Place saw on legs so that holes in bottom of saw line up with holes in top of legs.

3.Install screws, washers, Iockwashers and nuts as shown.

SAW BASE 17

END

STIFFENER"_t

 

FLAT WASHER---__

'

LOCKWASHER"_'_'

 

.Ex

/

/

13

If you mount the saw on any other bench, make sure that there is an opening in the/top of the bench the same size as the opening in the bottom of the saw so that the sawdust can drop through. Recommended working height is 33 to 37 inches from the top of the saw table to the floor.

ATTACHING AND ASSEMBLING TABLE EXTENSIONS

If you received Table Extensions with your saw (two furnished with Model No. 113.298031) or one furnished with Model No. 113.298151 ) attach them at this time.

If you have only one Table Extension, it may be attached to either side.

NOTE: When the Table Extension is attached to the left

side, it offers more support to the workpiece, especially when crosscutting or mitering long boards. When attached to the right side, it offers more support when curing wide panels.

If you attach the Extension to the left side, be sure to construct the Auxiliary Fence/Work Support and Push Block shown in "Basic Saw Operation" section.

1.From among the loose parts find the following hardware. NOTE: Double number of hardware if assembling extensions for Model 113.298031.

2 Corner Support Brackets

2 Corner Stiffener Brackets

8 Truss Hd. Screws 1/4-20 x 1

8 Ext. Lockwashers 1/4

8 Hex Nut 1/4-20

4 Hex Hd. Screws 5/16-18 x 1-1/4 4 Ext, Lockwasher 5/16

4 Hex Nut 5/16 - 18

Assemble brackets with hardware as listed.

Insert 5/16-18 x 1-1/4 in. long screws through holes in

EXTENSION then through table. Install flat washer, Iockwasbers, and screw on the nuts . . . DO NOT

TIGHTEN.

BLOCK OF WOOD

\

/

Align front edge of extension with front edge of saw table. Pull Extension UPWARDS above table surface ...

SLIGHTLY TIGHTEN SCREWS using 1/2 in. wrench.

Using small block of hardwood and hammer, l:ap extension DOWNWARDS at front, center & rear, unti it is EVEN with table surface ... TIGHTEN SCREWS.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents SAW with Legs TWO Table Extensions Motor SAW onlySAW with Legs Onetableextension Motor S.AGeneral Safety Instructions For Power Tools See Basic SAW Operation Adjustments Maintenance Stability SAWProtection EYES, HANDS, FACE, EARS, Body Connectin G to Power Source Outlet Think SafetyUSE only Accessories Designed for this SAW Volts Catalog No 3450 11120 1217 110-120 1220Check Motor Rotation ContentsUnpacking and Checking Contents Installing Handwheels AssemblyChecking Table Insert 32 I NChecking Blade for Heel Checking Blade Squareness to TableAssembling Steel Legs Side StiffenerTighten Attaching and Assembling Table ExtensionsInstalling RIP Fence Guide Bars and Switch BOX Thicknesses of Paper Raise blade all the way upAligning RIP Fence Adjusting RIP Scale Pointer HEX Installing Blade GuardHEX HD. Screws Do not TightenParallel SpreaderThinner Space Equal to Approx Looking Down on SAWOutlet When Changing Motor Rotation Mounting the MotorCheck Motor Rotation Clampscrew CoverEdge of Washer Even with ENDInstall Installing Belt GuardPlugging in Motor On-Off Switch has a locking feature. this Feature ON-OFF SwitchGetting to Know Your SAW RiP FenceBlade Tilt Or Squareness of Blade to Table Always Lock IT Securely When NuseBlade Guard not Shown for Picture Clarity Front of SAWOperation Basic SAWWork Helpers Push Stick and Push BlockRepetitive Cutting CrosscuttingCompound Miter Cutting Miter CuttingResawing and Rabbeting are performed using Addition to the Safety Instructions on Pages 2, 3.RIPPING, Bevel RIPPING, PLOUGHING, Molding KickbackPush Block Ploughing and MoldingCutting Panels ResawingRabbeting Do not Back UP Reverse Feeding WhileHeeling Adjustment Miter GaugeSawblade to Miter Gauge Groove OFF and Remove Plug from Power Source Outlet Blade TILT, or Squareness Blade to TableSpace Position AccuratePointer Does Not Handwheel MaintenancePointer TI LT MechanismRecommended Accessories CAT. noGuard Q Iter Guage Outlet Before Troubleshooting Trouble ShootingTrouble Probable Cause RemedyHave switch replaced Request voltage check from the power companyMotor starts slowly NotParts List for Craftsman 10 Inch Table SAW STD 31 41 4O Parts List for Craftsman 10 Inch Table SAW Lock 62705 Fence Assembly62693 Plug, Button 62692 Key Part Description 6270437893 37895Kevl Paff Description 60381 On/Off Parts Ljst for Craftsman 10 Inch Table SAWHardware for Attaching Legs to SAW Inch Table SAW SAW on LYSAW with Legs ONE Table Extension Motor
Top Page Image Contents