Sears 113.298141 owner manual Adjusting RIP Scale Pointer

Page 13

If the fence does not slide easily along the bars, the pressure of the spring can be REDUCED.

1.Loosen the screws.

2.Move spring slightly toward rear of fence ... tighten screws.

3, The rip fence must be PARALLEL with the sawblade (see page 29) and miter Gauge grooves... Move fence until it is along side of groove. Do NOT LOCK IT. It should be parallel to groove. If it is not;

A.Loosen the two "Hex. Head Screws."

B.Hold fence head tightly against bar ... move end of fence so that it is parallel with groove,

C.Altemately tighten the screws.

ADJUSTING RIP SCALE POINTER

1. Turn ELEVATION HANDWHEEL clockwise until blade is up as high as it_will go.

IMPORTANT: BLADE must be SQUARE (90 ° ) to TABLE, in order to ALIGN rip fence.

2.Position fence on right side of sawblade so that it touches the sides of the teeth ... tighten lock handle.

3.Loosen screw holding the pointer ... adjust pointer so that it points to "0" ... tighten screw.

NOTE: If you cannot adjust pointer so that it points to "0", loosen the _crews holding the front guide bar and move the guide bar.

HEX SCREWS

FENCE HEAD

LOCK HAi'_DLE

13

Image 13

Contents SAW with Legs TWO Table Extensions Motor SAW onlySAW with Legs Onetableextension Motor S.AGeneral Safety Instructions For Power Tools SAW See Basic SAW Operation Adjustments Maintenance StabilityProtection EYES, HANDS, FACE, EARS, Body Connectin G to Power Source Outlet Think SafetyUSE only Accessories Designed for this SAW Volts Catalog No 3450 11120 1217 110-120 1220Check Motor Rotation ContentsUnpacking and Checking Contents Installing Handwheels AssemblyChecking Table Insert 32 I NChecking Blade for Heel Checking Blade Squareness to TableAssembling Steel Legs Side StiffenerTighten Attaching and Assembling Table ExtensionsInstalling RIP Fence Guide Bars and Switch BOX Thicknesses of Paper Raise blade all the way upAligning RIP Fence Adjusting RIP Scale Pointer HEX Installing Blade GuardHEX HD. Screws Do not TightenParallel SpreaderThinner Space Equal to Approx Looking Down on SAWMounting the Motor Outlet When Changing Motor RotationCheck Motor Rotation Clampscrew CoverEdge of Washer Even with ENDInstall Installing Belt GuardPlugging in Motor On-Off Switch has a locking feature. this Feature ON-OFF SwitchGetting to Know Your SAW RiP FenceBlade Tilt Or Squareness of Blade to Table Always Lock IT Securely When NuseBlade Guard not Shown for Picture Clarity Front of SAWOperation Basic SAWWork Helpers Push Stick and Push BlockRepetitive Cutting CrosscuttingCompound Miter Cutting Miter CuttingResawing and Rabbeting are performed using Addition to the Safety Instructions on Pages 2, 3.RIPPING, Bevel RIPPING, PLOUGHING, Molding KickbackPush Block Ploughing and MoldingCutting Panels ResawingRabbeting Do not Back UP Reverse Feeding WhileMiter Gauge Heeling AdjustmentSawblade to Miter Gauge Groove Blade TILT, or Squareness Blade to Table OFF and Remove Plug from Power Source OutletSpace Accurate PositionPointer Does Not Handwheel MaintenancePointer TI LT MechanismCAT. no Recommended AccessoriesGuard Q Iter Guage Outlet Before Troubleshooting Trouble ShootingTrouble Probable Cause RemedyHave switch replaced Request voltage check from the power companyMotor starts slowly NotParts List for Craftsman 10 Inch Table SAW STD 31 41 4O Parts List for Craftsman 10 Inch Table SAW Lock 62705 Fence Assembly62693 Plug, Button 62692 Key Part Description 6270437893 37895Kevl Paff Description 60381 On/Off Parts Ljst for Craftsman 10 Inch Table SAWHardware for Attaching Legs to SAW SAW on LY Inch Table SAWSAW with Legs ONE Table Extension Motor