Sears 113.298141 owner manual Installing Belt Guard

Page 18

INSTALLING BELT GUARD

_

TOGETHER

_-_ TWO HOLES CLOSEST

1.Remove the belt and motor pulley.

2. Screws furnished

witli guard are "self threading"

...

BELT GUARD

SUPPORT BRACKET

\

10-32 X 1/2 IN.

SE L.F-THREADING

SCREW

screw them into holes		in	BELT GUARD		SUPPORT
BRACKET, then	remove	them.
3. Position BELT	GUARD		SUPPORT	BRACKET		and
BELT GUARD	SUPPORT		as shown	and	install	the
screws ... make sure motor shaft is in CENTER of
hole in SUPPORT.

4. Install three CLIPS (furnished with guardi 90 ° apart starting with one clip at the end of the guard as shown

•.. LONG END of cl p facingAWAY from you.

BELT GUARD

BELT GUARD

\

BELT GUARD SUPPORT

\

PIVOT SCREW

/

/

CENTERED

OPENING

j__,_CLIPS

N

LONG END

BELT.

5.Reinstall ,motor pulley the same way it was when you aligned the belt,

6.Place belt on SAW'PULLEY ,.. insert end of belt through opening in END of guard,

7.Slip belt over motor pulley.

18

Image 18

Contents SAW with Legs Onetableextension Motor SAW onlySAW with Legs TWO Table Extensions Motor S.AGeneral Safety Instructions For Power Tools See Basic SAW Operation Adjustments Maintenance Stability SAWProtection EYES, HANDS, FACE, EARS, Body USE only Accessories Designed for this SAW Think SafetyConnectin G to Power Source Outlet Volts Catalog No 3450 11120 1217 110-120 1220Contents Check Motor RotationUnpacking and Checking Contents Checking Table Insert AssemblyInstalling Handwheels 32 I NAssembling Steel Legs Checking Blade Squareness to TableChecking Blade for Heel Side StiffenerAttaching and Assembling Table Extensions TightenInstalling RIP Fence Guide Bars and Switch BOX Raise blade all the way up Thicknesses of PaperAligning RIP Fence Adjusting RIP Scale Pointer HEX HD. Screws Installing Blade GuardHEX Do not TightenThinner SpreaderParallel Space Equal to Approx Looking Down on SAWOutlet When Changing Motor Rotation Mounting the MotorCheck Motor Rotation Edge of Washer CoverClampscrew Even with ENDInstalling Belt Guard InstallPlugging in Motor Getting to Know Your SAW ON-OFF SwitchOn-Off Switch has a locking feature. this Feature RiP FenceAlways Lock IT Securely When Nuse Blade Tilt Or Squareness of Blade to TableFront of SAW Blade Guard not Shown for Picture ClarityWork Helpers Basic SAWOperation Push Stick and Push BlockCrosscutting Repetitive CuttingMiter Cutting Compound Miter CuttingRIPPING, Bevel RIPPING, PLOUGHING, Molding Addition to the Safety Instructions on Pages 2, 3.Resawing and Rabbeting are performed using KickbackPloughing and Molding Push BlockRabbeting ResawingCutting Panels Do not Back UP Reverse Feeding WhileHeeling Adjustment Miter GaugeSawblade to Miter Gauge Groove OFF and Remove Plug from Power Source Outlet Blade TILT, or Squareness Blade to TableSpace Position AccuratePointer Does Not Pointer MaintenanceHandwheel TI LT MechanismRecommended Accessories CAT. noGuard Q Iter Guage Trouble Probable Cause Trouble ShootingOutlet Before Troubleshooting RemedyMotor starts slowly Request voltage check from the power companyHave switch replaced NotParts List for Craftsman 10 Inch Table SAW STD 31 41 4O Parts List for Craftsman 10 Inch Table SAW 62705 Fence Assembly Lock37893 Key Part Description 6270462693 Plug, Button 62692 37895Parts Ljst for Craftsman 10 Inch Table SAW Kevl Paff Description 60381 On/OffHardware for Attaching Legs to SAW Inch Table SAW SAW on LYSAW with Legs ONE Table Extension Motor