Sterling 882.00274.00 specifications Spare Parts List, Exploded Assembly Drawing Parts List

Page 45

7-5 Spare Parts List

Figure 8: Exploded Assembly Drawing

Figure 9:	Parts List

Detail #	Part number	Part/assembly description
1	A0541207	Supply Hopper, 1.0 Cubic Foot
1	A0541208	Supply Hopper, 2.0 Cubic Foot
2	A0541225	Hopper Cover, Manual Fill
2	A0541226	Hopper Cover with Cutout for .1 Cubic Foot Hopper Loader
2	A0541227	Hopper Cover with Cutout for .25 Cubic Foot Hopper Loader
3	A0541286	Magnetic Stripping for Supply Hopper Cover
4	A0541285	Screw, ¼-20 x ½", HHC, Grade 5
5	A0101190	Lock Washer, ¼"
6	A0541206	Supply Hopper Sight Glass
7	W0012471	Blind Rivet, 3/16"
8	W00052210	Plunger Pin, Retractable
9	A0541201	Material Transfer Tube
10	A0541202	Main Throat, Standard, 6"
10	A0541208	Main Throat, Optional Expanded, 8"
11	A0541205	Main Throat Sight Glass
12	A0069242	Flat Washer, 5/16
13	W00001948	Screw, 3/8-16 x ½"
14	A0069203	Lock Washer, 3/8"
15	A0069458	Screw, 3/8-16 x 3/4"
16	A0541216	Calibration Sample Port Plate
17	A0541215	Clean Out Port Plate
18	A0540904	Screw, 10-32 x ½"

Additive Feeders

Chapter 7: Appendix

44 of 50

Image 45

Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting Safety How to Use This ManualSafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityMechanical Features Standard FeaturesFunctional Description Models Covered in This ManualElectrical Features Controller FeaturesOptions Accessories Safety Devices and Interlocks Safety Circuit StandardsFail Safe Operation Safety Device Lock-Outs Supply System Installation InstallationUncrating the Equipment Rigging and Placing the Additive FeederMain Power Connection Electrical ConnectionsControl Relay Connection Determining the Desired Feed Rate Setup Procedures110 100 Calibration Procedure ProcedureEquipment Needed Observed Feed Rates ExamplesPre-Startup Checks Initial Start-upStarting Up the Additive Feeder Shutting Down the Additive FeederIndicator Lights SwitchesOperation Start-upTimer Module Used as a Cycle Override Safety TimerCounter Module Elapsed Time Module Regrind Feeder with Proximity Switch Dual Setpoint Control Operation 2 Component ApplicationsSet Point #2 Motor Control Bottom Low Level Extruder Tracking Control Extruder Tracking Installation and SetupExtruder Tracking Equation Field Control Programming Desired Display SettingEquation Motor RPM = 25.2 X Auger RPMProgramming Mode Viewing or Changing the ConstantProgramming for Follower Operation Viewing or Changing the Program Maximum Setting Viewing or Changing the Program Minimum SettingExiting Programming Mode and Returning to Run Mode Program Minimum SettingShutting Down the Additive Feeder Additive Feeder Control Factory DefaultsMaintenance Preventative Maintenance SchedulePhotocopy this page for your maintenance records Material Cleanout/Changeover Preventative MaintenanceAuger Assembly Changeover Corrective MaintenanceRemoving Auger Assembly Installing Auger AssemblyReplacement Motor Brush Part Numbers Motor Brush ReplacementTroubleshooting Problem Possible cause Corrective actionIntroduction Additive Feeders Troubleshooting Appendix WarrantyOptional Components Annex B Information Technical SpecificationsAdditive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers SET Point Exploded Assembly Drawing Parts List Spare Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Warranty Returns Safety Tag InformationAdditive Feeder Safety Tags Returned Material PolicyTechnical Assistance Additive Feeder Identification Serial Number TagPhotocopy this page for your records Worksheet for Charting Feed Rates