Sterling 882.00274.00 Viewing or Changing the Program Minimum Setting, Program Constant

Page 31

Viewing or Changing the Program Minimum Setting

1.Enter the programming mode, then flip DIP switch 2, Program Minimum Setting, to ON.

2.The current value for the lower limit FACTORY SETTING = 0 will appear in the LED display.

3.Use the Up or Down buttons to change the lower limit, as desired.

4.When finished, flip DIP switch 2 to OFF.

5.The display should read PROG.

Viewing or Changing the Program Maximum Setting

1.Enter the programming mode, then flip DIP switch 3, PROGRAM MAXIMUM SETTING to ON.

2.The current value for the upper limit FACTORY SETTING = 70 will appear in the LED display.

3.Use the Up or Down buttons to change the upper limit, as desired.

4.When finished, flip DIP switch 3 to OFF.

5.The display should read PROG.

Exiting Programming Mode and Returning to Run Mode

1.Make sure DIP switches 4, TIME/RATE MODE SELECT, and 5,

MASTER/FOLLOWER MODE SELECT are in the desired positions factory

Setting 4 = 1, 5 = OFF, ON FOR OPTIONAL EXTRUDER TRACKER CONTROLS BEFORE entering the RUN mode (DIP switch 7 OFF).

2.Make sure DIP switches 1 through 4 are OFF.

3.If satisfied with the programmed values, flip DIP switch 7 to OFF.

4.Control should begin to operate normally, using the values and modes selected.

Figure 3: DIP Switch Function Table

Switch 1

Program Constant

 

Switch 2

Program Minimum Setting

 

Switch 3

Program Maximum Setting

 

Switch 4

Decimal Select

0 – 4 = Decimal Points

Switch 5

Master/Follower Select

OFF = Master ON = Follower

Switch 6

Do Not Use – Set to OFF

 

Switch 7

Program/Run Select

OFF = Run ON = Program

Switch 8

Do Not Use – Set to OFF

 

Additive Feeders

Chapter 4: Operation

30 of 50

Image 31
Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityModels Covered in This Manual Standard FeaturesMechanical Features Functional DescriptionController Features Electrical FeaturesOptions Accessories Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-Outs Rigging and Placing the Additive Feeder InstallationSupply System Installation Uncrating the EquipmentElectrical Connections Main Power ConnectionControl Relay Connection Determining the Desired Feed Rate Setup Procedures110 100 Procedure Calibration ProcedureEquipment Needed Observed Feed Rates ExamplesShutting Down the Additive Feeder Initial Start-upPre-Startup Checks Starting Up the Additive FeederStart-up SwitchesIndicator Lights OperationUsed as a Cycle Override Safety Timer Timer ModuleCounter Module Elapsed Time Module Dual Setpoint Control Operation 2 Component Applications Regrind Feeder with Proximity SwitchSet Point #2 Motor Control Bottom Low Level Extruder Tracking Control Extruder Tracking Installation and SetupExtruder Tracking Equation Motor RPM = 25.2 X Auger RPM Desired Display SettingField Control Programming EquationViewing or Changing the Constant Programming ModeProgramming for Follower Operation Program Minimum Setting Viewing or Changing the Program Minimum SettingViewing or Changing the Program Maximum Setting Exiting Programming Mode and Returning to Run ModeShutting Down the Additive Feeder Additive Feeder Control Factory DefaultsPreventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Material Cleanout/Changeover Preventative MaintenanceInstalling Auger Assembly Corrective MaintenanceAuger Assembly Changeover Removing Auger AssemblyReplacement Motor Brush Part Numbers Motor Brush ReplacementProblem Possible cause Corrective action TroubleshootingIntroduction Additive Feeders Troubleshooting Appendix WarrantyOptional Components Annex B Information Technical SpecificationsAdditive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers SET Point Exploded Assembly Drawing Parts List Spare Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Returned Material Policy Safety Tag InformationWarranty Returns Additive Feeder Safety TagsTechnical Assistance Additive Feeder Identification Serial Number TagPhotocopy this page for your records Worksheet for Charting Feed Rates