Sterling 882.00274.00 Returned Material Policy, Safety Tag Information, Credit Returns

Page 49

7-6 Returned Material Policy

Credit Returns

Prior to the return of any material authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned.

Reason for requesting the return must be given.

ALL returned material purchased from the manufacturer returned is subject to 15% ($75.00 minimum) restocking charge.

ALL returns are to be shipped prepaid.

The invoice number and date or purchase order number and date must be supplied.

No credit will be issued for material that is not within the manufacturer’s warranty period and/or in new and unused condition, suitable for resale.

Warranty Returns

Prior to the return of any material, authorization must be given by the manufacturer. A RMA number will be assigned for the equipment to be returned.

Reason for requesting the return must be given. All returns are to be shipped prepaid.

The invoice number and date or purchase order number and date must be supplied.

After inspecting the material, a replacement or credit will be given, at the manufacturer’s discretion. If the item is found to be defective in materials or workmanship, and it was manufactured by our company, purchased components are covered under their specific warranty terms.

7-7 Safety Tag Information

Additive Feeder Safety Tags

Read Operation

and Installation

Manual

High Voltage

Inside Enclosure

PE

Lifting Point

Shear Hazard Rotating Auger

Earth Ground

Protected Earth Ground

Additive Feeders

Chapter 7: Appendix

48 of 50

Image 49
Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityMechanical Features Standard FeaturesFunctional Description Models Covered in This ManualController Features Electrical FeaturesOptions Accessories Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-Outs Supply System Installation InstallationUncrating the Equipment Rigging and Placing the Additive FeederElectrical Connections Main Power ConnectionControl Relay Connection Determining the Desired Feed Rate Setup Procedures110 100 Procedure Calibration ProcedureEquipment Needed Observed Feed Rates ExamplesPre-Startup Checks Initial Start-upStarting Up the Additive Feeder Shutting Down the Additive FeederIndicator Lights SwitchesOperation Start-upUsed as a Cycle Override Safety Timer Timer ModuleCounter Module Elapsed Time Module Dual Setpoint Control Operation 2 Component Applications Regrind Feeder with Proximity SwitchSet Point #2 Motor Control Bottom Low Level Extruder Tracking Control Extruder Tracking Installation and SetupExtruder Tracking Equation Field Control Programming Desired Display SettingEquation Motor RPM = 25.2 X Auger RPMViewing or Changing the Constant Programming ModeProgramming for Follower Operation Viewing or Changing the Program Maximum Setting Viewing or Changing the Program Minimum SettingExiting Programming Mode and Returning to Run Mode Program Minimum SettingShutting Down the Additive Feeder Additive Feeder Control Factory DefaultsPreventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Material Cleanout/Changeover Preventative MaintenanceAuger Assembly Changeover Corrective MaintenanceRemoving Auger Assembly Installing Auger AssemblyReplacement Motor Brush Part Numbers Motor Brush ReplacementProblem Possible cause Corrective action TroubleshootingIntroduction Additive Feeders Troubleshooting Appendix WarrantyOptional Components Annex B Information Technical SpecificationsAdditive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers SET Point Exploded Assembly Drawing Parts List Spare Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Warranty Returns Safety Tag InformationAdditive Feeder Safety Tags Returned Material PolicyTechnical Assistance Additive Feeder Identification Serial Number TagPhotocopy this page for your records Worksheet for Charting Feed Rates