Sterling 882.00274.00 specifications A0541292 Auger Assembly, 1/2

Page 46

Detail #	Part number	Part/assembly description
19	W00052550	Knob, Knurled
20	A0069218	Stop Nut, 5/16-18
21	A0069549	Flat Washer, 3/8"
22	A0541279	Screw, 5/16-18 x 4½"
23	A0069241	Flat Washer, ¼"
24	A0541277	Quick Release Pin
25	A0541209	Feed Tube Insert, 1/2"
25	A0541210	Feed Tube Insert, 3/4"
25	A0541211	Feed Tube Insert, 1"
25	A0541212	Feed Tube Insert, 1 1/4"
25	A0541213	Feed Tube Insert, 1 1/2"
25	A0541214	Feed Tube Insert, 1 3/4"
26	A0541219	Auger, 1/2"
26	A0541220	Auger, 3/4"
26	A0541219	Auger, 1"
26	A0541292	Auger, 1 1/4"
Assy.	A0541292	Auger Assembly, 1/2" *
Assy.	A0541293	Auger Assembly, 3/4" *
Assy.	A0541294	Auger Assembly, 1" *
Assy.	A0541295	Auger Assembly, 1 1/4" *
Assy.	A0541296	Auger Assembly, 1 1/2"
Assy.	A0541297	Auger Assembly, 1 3/4"
27	W00015504	Roll Pin
28	A0541284	O Ring
29	A0541217	Thrust Bearing
30	A0541283	Compression Spring
31	W00000947	Lock Washer, #10
32	A0103129	Terminal Ring for Retaining Cable
33	W00013647	Pin Retaining Cable
34	A0541229	Motor Mount
35	A0541282	Jaw Coupler
36	A0555661	Motor Assy, 115 VAC, 1/10 H.P.
36	A0541298	Motor Assembly, 115 VAC 1/20 H.P.
36	A0547487	Motor Assembly, 115 VAC, Low RPM 1/20 H.P.
37	A0541265	Control, 115 VAC
37	A0541266	Control, 115 VAC, Timer/Cycle Counter
37	A0541267	Control, 115 VAC, Timer/Elapsed Timer
37	A0541268	Control, 115 VAC, Extruder Tracking
37	A0541269	Control, 115 VAC, Extruder Tracking, Timer/Elapsed Timer
37	A0544795	230 VAC/115 VAC Transformer Control Assembly
38	A0541039	Strain Relief for Control Cable
39	A0541262	Lock Nut for Strain Relief
	A0539035	Transition Flange, Feed Throat, 7" to 4" Square

*Auger assemblies include details 26, 27, 28, 29, 30, & 12. Order the appropriately-sized feed tube insert (Detail 25) if needed.

Additive Feeders

Chapter 7: Appendix

45 of 50

Image 46

Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility RememberMaintenance Responsibility Reporting a Safety DefectFunctional Description Standard FeaturesMechanical Features Models Covered in This ManualController Features Electrical FeaturesOptions Accessories Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-Outs Uncrating the Equipment InstallationSupply System Installation Rigging and Placing the Additive FeederElectrical Connections Main Power ConnectionControl Relay Connection Setup Procedures Determining the Desired Feed Rate110 100 Procedure Calibration ProcedureEquipment Needed Examples Observed Feed RatesStarting Up the Additive Feeder Initial Start-upPre-Startup Checks Shutting Down the Additive FeederOperation SwitchesIndicator Lights Start-upUsed as a Cycle Override Safety Timer Timer ModuleCounter Module Elapsed Time Module Dual Setpoint Control Operation 2 Component Applications Regrind Feeder with Proximity SwitchSet Point #2 Motor Control Bottom Low Level Extruder Tracking Installation and Setup Extruder Tracking ControlExtruder Tracking Equation Equation Desired Display SettingField Control Programming Motor RPM = 25.2 X Auger RPMViewing or Changing the Constant Programming ModeProgramming for Follower Operation Exiting Programming Mode and Returning to Run Mode Viewing or Changing the Program Minimum SettingViewing or Changing the Program Maximum Setting Program Minimum SettingAdditive Feeder Control Factory Defaults Shutting Down the Additive FeederPreventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Preventative Maintenance Material Cleanout/ChangeoverRemoving Auger Assembly Corrective MaintenanceAuger Assembly Changeover Installing Auger AssemblyMotor Brush Replacement Replacement Motor Brush Part NumbersProblem Possible cause Corrective action TroubleshootingIntroduction Additive Feeders Troubleshooting Warranty AppendixOptional Components Technical Specifications Annex B InformationDrawings and Diagrams Additive Feeder Specifications and Overall DimensionsTypical Additive Feeder Controllers SET Point Spare Parts List Exploded Assembly Drawing Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Additive Feeder Safety Tags Safety Tag InformationWarranty Returns Returned Material PolicyAdditive Feeder Identification Serial Number Tag Technical AssistanceWorksheet for Charting Feed Rates Photocopy this page for your records