Sterling 882.00274.00 specifications Programming Mode, Viewing or Changing the Constant

Page 30

Programming Mode

The motor will stop when in Programming mode.

1.Make sure DIP switches 1 through 4 and 7 and 8 are OFF.

2.Flip switch 7 to ON.

3.The display should read PROG.

4.Follow the instructions given below to view and/or edit any of the variables.

Viewing or Changing Displayed Decimal Place/Rate or Time Mode Select

1.Make sure you are in Programming Mode, then flip DIP switch 4, RATE-TME

MODE/PROGRAM DECIMAL PLACE, ON.

2.The current decimal point setting, if any, FACTORY SETTING = 0, will be displayed.

3.Use the Up or Down buttons to change the decimal point as desired. Use 0 for NO decimal point.

4.When finished, flip DIP switch 4 to OFF.

5.The display should read PROG (the decimal point, if any, is also displayed).

Viewing or Changing the Constant

1.Calculate the constant for your application using the formula listed on the previous page.

2.Make sure you are in Programming Mode, then flip DIP switch 1, PROGRAM CONSTANT, to ON.

3.The current value for the constant, FACTORY SETTING = 30, should not be visible on the LED display.

4.Use the Up or Down buttons to adjust the constant value.

5.When finished, flip DIP switch 1 to OFF.

6.The display should read PROG.

The display setting is set to the slowest speed when you exit the Programming Mode.

Programming for Follower Operation

1.Enter Programming Mode, then turn DIP switches 5, MASTER/FOLLOWER SELECT, and 1, PROGRAM CONSTANT, to ON.

2.Set constant to:

CONSTANT = 1000 x PULSES PER REVOLUTION OF MASTER PULSES PER REVOLUTION OF FOLLOWER = 30.0

3.Turn OFF switches 1 and 7.

4.Turn OFF AC power, then reapply AC power. The control is now set for follower operation.

Additive Feeders

Chapter 4: Operation

29 of 50

Image 30

Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting Safety How to Use This ManualSafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility RememberMaintenance Responsibility Reporting a Safety DefectFunctional Description Standard FeaturesMechanical Features Models Covered in This ManualElectrical Features Controller FeaturesOptions Accessories Safety Devices and Interlocks Safety Circuit StandardsFail Safe Operation Safety Device Lock-Outs Uncrating the Equipment InstallationSupply System Installation Rigging and Placing the Additive FeederMain Power Connection Electrical ConnectionsControl Relay Connection Setup Procedures Determining the Desired Feed Rate110 100 Calibration Procedure ProcedureEquipment Needed Examples Observed Feed RatesStarting Up the Additive Feeder Initial Start-upPre-Startup Checks Shutting Down the Additive FeederOperation SwitchesIndicator Lights Start-upTimer Module Used as a Cycle Override Safety TimerCounter Module Elapsed Time Module Regrind Feeder with Proximity Switch Dual Setpoint Control Operation 2 Component ApplicationsSet Point #2 Motor Control Bottom Low Level Extruder Tracking Installation and Setup Extruder Tracking ControlExtruder Tracking Equation Equation Desired Display SettingField Control Programming Motor RPM = 25.2 X Auger RPMProgramming Mode Viewing or Changing the ConstantProgramming for Follower Operation Exiting Programming Mode and Returning to Run Mode Viewing or Changing the Program Minimum SettingViewing or Changing the Program Maximum Setting Program Minimum SettingAdditive Feeder Control Factory Defaults Shutting Down the Additive FeederMaintenance Preventative Maintenance SchedulePhotocopy this page for your maintenance records Preventative Maintenance Material Cleanout/ChangeoverRemoving Auger Assembly Corrective MaintenanceAuger Assembly Changeover Installing Auger AssemblyMotor Brush Replacement Replacement Motor Brush Part NumbersTroubleshooting Problem Possible cause Corrective actionIntroduction Additive Feeders Troubleshooting Warranty AppendixOptional Components Technical Specifications Annex B InformationDrawings and Diagrams Additive Feeder Specifications and Overall DimensionsTypical Additive Feeder Controllers SET Point Spare Parts List Exploded Assembly Drawing Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Additive Feeder Safety Tags Safety Tag InformationWarranty Returns Returned Material PolicyAdditive Feeder Identification Serial Number Tag Technical AssistanceWorksheet for Charting Feed Rates Photocopy this page for your records