Sterling 882.00274.00 specifications Technical Specifications, Annex B Information

Page 41

7-3 Technical Specifications

Annex B Information

The following design information is provided for your reference:

1.	No modifications are allowed to this equipment that could alter the CE compliance
2.	Ambient temperature:	0 degrees Celsius – Maximum (104 degrees Fahrenheit)
3.	Humidity range:	50% relative humidity
4.	Altitude:	Sea level
5.	Environment:	Clean, dust-free and non-explosive
6.	Radiation:	None
7.	Vibration:	Minimal, i.e. machine mounting
8.	Allowable voltage fluctuation:		+/- 10%
9.	Allowable frequency fluctuation:		Continuous	+/- 1%
			Intermittent	+/- 2%
10.	Nominal supply voltage:	460/3/60 (Verify on serial number tag)

11.Earth ground type: TN (system has one point directly earthed through a protective conductor)

12.Power supply should include a ground connection.

13.Over-current protection is supplied in the additive feeder, but additional protection should be supplied by the user.

14.The door-mounted disconnect serves as the electrical disconnect device.

15.Additive feeder is not equipped with local lighting.

Additive Feeders

Chapter 7: Appendix

40 of 50

Image 41

Contents SF Series Additive Feeders Parts and Service Department Shipping Information Table of Contents Troubleshooting Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityMechanical Features Standard FeaturesFunctional Description Models Covered in This ManualOptions Electrical FeaturesController Features Accessories Fail Safe Operation Safety Devices and InterlocksSafety Circuit Standards Safety Device Lock-Outs Supply System Installation InstallationUncrating the Equipment Rigging and Placing the Additive FeederControl Relay Connection Main Power ConnectionElectrical Connections Determining the Desired Feed Rate Setup Procedures110 100 Equipment Needed Calibration ProcedureProcedure Observed Feed Rates ExamplesPre-Startup Checks Initial Start-upStarting Up the Additive Feeder Shutting Down the Additive FeederIndicator Lights SwitchesOperation Start-upCounter Module Timer ModuleUsed as a Cycle Override Safety Timer Elapsed Time Module Set Point #2 Motor Control Bottom Low Level Regrind Feeder with Proximity SwitchDual Setpoint Control Operation 2 Component Applications Extruder Tracking Control Extruder Tracking Installation and SetupExtruder Tracking Equation Field Control Programming Desired Display SettingEquation Motor RPM = 25.2 X Auger RPMProgramming for Follower Operation Programming ModeViewing or Changing the Constant Viewing or Changing the Program Maximum Setting Viewing or Changing the Program Minimum SettingExiting Programming Mode and Returning to Run Mode Program Minimum SettingShutting Down the Additive Feeder Additive Feeder Control Factory DefaultsPhotocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Material Cleanout/Changeover Preventative MaintenanceAuger Assembly Changeover Corrective MaintenanceRemoving Auger Assembly Installing Auger AssemblyReplacement Motor Brush Part Numbers Motor Brush ReplacementIntroduction TroubleshootingProblem Possible cause Corrective action Additive Feeders Troubleshooting Appendix WarrantyOptional Components Annex B Information Technical SpecificationsAdditive Feeder Specifications and Overall Dimensions Drawings and DiagramsTypical Additive Feeder Controllers SET Point Exploded Assembly Drawing Parts List Spare Parts ListA0541292 Auger Assembly, 1/2 One Component Control Enclosure Parts Identification Two Component Control Enclosure Parts Identification Warranty Returns Safety Tag InformationAdditive Feeder Safety Tags Returned Material PolicyTechnical Assistance Additive Feeder Identification Serial Number TagPhotocopy this page for your records Worksheet for Charting Feed Rates