Grizzly G4015Z owner manual Drill Press Controls

Page 27

SECTION 7: DRILL PRESS

CONTROLS

Drill Press Speeds

The speed of the drill press spindle is controlled by 2 groups of belts and pulleys. The belt posi- tions on the end of the lathe control one speed range. See Figure 23. The belts and pulleys above the drill press control the other range. See Figure 24.

�����

�������

������

����

���������

������

������

�����

������

������������������

���

���

���� ���� ���� ���� ���� ���� ���

�������� ���� ���� ���� ���� ���� ����

�������� ���� ���� ���� ���� ���� ���

Figure 23. Lower pulleys for speed changes.

Figure 24. Upper pulleys for speed changes.

Figure 25. Speed chart.

Disconnect the power before changing speeds or making adjustments to this machine. Failure to do this may result in serious personal injury.

Unplug the Lathe/Mill! Before using the drill press, the hub at the end of the lathe spindle must be adjusted to the “in” position. See Figure

25.To ease engagement of this hub, slowly rotate the drill spindle by hand while applying pressure to the hub.

The chart also shows the various combinations of belt positions for achieving a desired speed.

Example:

To select a spindle speed of 310 R.P.M., start by moving the belts at the end of the lathe. Move the lower belt to the “B” position. Move the upper belt to the “F” position. Follow the belt changing pro- cedures in the section titled Lathe Speeds.

Next, move the belt located above the drill press to the “L-H” position.

G4015Z Lathe/Mill

-25-

Image 27
Contents Model G4015Z Combination LATHE/MILL Page Table Of Contents Safety Instructions For Power Tools SafetyAMP Rating Never Leave a Chuck KEY in the Drill Chuck or Lathe Chuck Additional Safety Instructions For Lathe/Mills110V Operation Extension Cords Circuit RequirementsTypical 110V plug and outlet G4015Z Lathe/Mill GroundingCommentary IntroductionPiece Inventory UnpackingUse only these lifting points G4015Z Lathe/Mill Lifting MachineSite Considerations Clean UpMachine Terms IdentificationAssembly & Setup HandwheelHand Crank Place roll pin in hole and tap with hammer Lathe ChuckPlease see Figure Lathe Chuck RemovalIf the chuck is still tight on the spindle To install a chuckDead Center Tool Post Using a center to check tool bit height G4015 Lathe/MillDrill Chuck Drill Chuck RemovalUnplug the machine Lathe Mounting Drill Press MountingSliding the tool post off Machine ViseTo change belt position Unplug the machine Lathe ControlsLathe Speeds ExampleNever move the feed rate lever while machine is running Feed Selection Feed LeverCarriage Lock Half Nut Carriage ControlsTailstock Controls Drill Press Controls Fine Down Feed Quill Lock LeverGibs AdjustmentsThis bolt locks the apron in place Head StockBar stock mounted on centers G4015Z Lathe/Mill TailstockTailstock offset adjustment screw G4015Z Lathe/Mill Control Panel OperationsBefore starting the machine Test RunReading the Charts Feed RatesSelection Swing gears in lower position Changing GearsFlats on bushing align with slot Inch Threading Tooth gear installed at a G4015 Lathe/Mill127 tooth combination gear Gear D is turned so hub is on outside G4015 Lathe/Mill Metric ThreadingLubrication MaintenanceTailstock oiling points Bearing PreloadClosure Machine Data Sheet Your Notes 856 852 857 880 Link Board 872 871 601 606 Clutch 127 119 Motor 142 Body 218 223 305 304 301 222 214 216 Draw BAR G4015 Lathe/Mill Locking HUB 547 Lock HUB Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC