DeWalt instruction manual Quick Start Guide D24000 Wet Tile Saw, Step

Page 6

English

USE SPLASH GUARD FOR EVERY OPERATION FOR WHICH IT CAN BE USED.

REPLACE DAMAGED CUTTING WHEEL BEFORE OPERATING.

DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

NEVER USE PAN HEATER OR OTHER HEATER SOURCE FOR HEATING WATER. DAMAGE TO THE TOOL, FIRE OR PERSONAL INJURY COULD RESULT.

THINK! YOU CAN PREVENT ACCIDENTS.

ON CUTTING WHEEL COVER

CAUTION: PROPERLY SECURE COVER WITH BOTH SCREWS BEFORE USE.

ON CART

WARNING: TO REDUCE THE RISK OF INJURY, ALWAYS VERIFY THE CUTTING WHEEL IS ADJUSTED TO THE CORRECT HEIGHT AND LOCATION IN THE CENTER OF THE CART GROOVE BEFORE OPERATING SAW.

Quick Start Guide

D24000 Wet Tile Saw

WARNING: For your own safety, read the instruction manual before operating the wet tile saw. Failure to heed these warnings may result in personal injury and serious damage to the saw. When servicing this tool, use only identical replace- ment parts. Have damaged cords replaced by an authorized service center.

FIG. 1

The motor arm assembly comes assembled. Open the box and lift the assembly out, as shown in Figure 1.

Step 1

1.Install the motor arm onto frame assembly. Using the wrench supplied, install and tighten the two screws closest to the rail first. Install and tighten the other two screws.

Step 2

2.Attach the cutting wheel.

a.Using the smaller Allen wrench supplied, loosen (do not remove) the screw on the side of the cutting wheel cover. Pull the rub- ber side flap back and lift the cover toward the rear of the saw.

b.Press spindle lock button. Remove the cut- ting wheel nut with hex wrench provided. Remove outer flange.

c.Install the cutting wheel with the rotational arrow facing the same way as on the rota- tional arrow on the cutting wheel cover. Press the spindle lock button while tighten- ing the cutting wheel nut.

d.Replace cover and tighten screw.

For further details, refer to

To Attach Cutting Wheel

in the

Instruction Manual.

4

Image 6
Contents Dewalt English DEWALT… Built Jobsite ToughTable of Contents Important Safety Instructions for All Tools Grounding InstructionsAWG Additional Safety Rules for Wet Tile Saw Would be 3 76mm or Less from Cutting WheelQuick Start Guide D24000 Wet Tile Saw StepSteps 5, 6, 7 Attach the cutting cart to the railsFeatures Fig Assembly FigTo Attach Cutting Wheel FIG Operation Locking the Cutting Cart Fig Types of Cuts FigsAdjustments Fig Maintenance AccessoriesTroubleshooting Guide Be Sure to Follow Safety Rules and InstructionsFrançais DEWALT… DE Conception Robuste Pour LE ChantierEwalt Table DES Matières Consignes de sécurité importantes concernant tous les outils Directives Concernant LA Mise À LA TerreFrançais Français Guide de démarrage Coupe-tuile à l’eau D24000 ÉtapeFixer de la lame Étapes 5, 6, 7 Fixer l’établi de coupe aux mon- tantsEnsemble du bras moteur Composants àAssemblage à Fixation DE LA Lame FIGFonctionnement Réalisation d’une coupe fig Verrouillage de l’établi de coupe figTypes de Coupes à Réglages à Entretien Lames AccessoiresGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANGuide de dépannage QUE SE PASSE-T-IL?Quoi FAIRE… Español DEWALT…PARA Trabajos PesadosÍndice Instrucciones DE Conexión a Tierra 120V 15,2 15,2-30,4Más No más Reglas de seguridad adicionales para sierras de corte húmedo Español Guía de referencia rápida Sierra de corte húmedo D24000 PasoEspañol Pasos 5, 6, 7 Conecte el carro de corte a los rielesCaracterísticas Fig Ensamblaje FigPara Conectar EL Disco DE Corte FIG Operación Bloqueo del carro de corte Fig Profundidad del disco de corte FigRealización del corte Fig Tipos de corte FigAjustes Fig Transporte y almacenamiento MantenimientoEscobillas Fig LimpiezaPóliza de Garantía ReparacionesAccesorios Garantía limitada por tres añosGuía de resolución de problemas Asegúrese DE Seguir LAS Reglas E Instrucciones DE SeguridadD24000