DeWalt D24000 instruction manual Steps 5, 6, 7, Attach the cutting cart to the rails

Page 7

Step 3

3. Attach the cutting cart to the rails.

For further details, refer to

Assembly in the

Instruction Manual.

NOTE: Make sure the cart lock is in full open position.

a. Align the arrow on the rear of the cutting cart with the round rail on the frame of the saw.

b. Place the rear roller assembly onto the round rail.

Step 4

4.The outer rim of the cutting wheel should always be at least 3/16" (5mm) below the cart surface. Push cart entirely through the cutting wheel before cutting to be sure that the cutting wheel depth is properly adjusted to avoid cutting the cart. Adjust the depth of cut knob (BB) and tighten the locking wing nut (MM), then the head lock knob

(D).

For further details, refer

to Adjustments in

the Instruction Manual.

BB

			3/16" (5MM)	English

D

c. Slide the cutting cart assembly onto the rail system. Tilt the front of the cart upward slightly to clear the cart stop.

MM

Steps 5, 6, 7, 8

5.Place the saw in the water pan. The water pan drain hole should be in the front position.

6.Attach the water pump to the water line and insert pump power cord into the socket. Position pump properly in pan, as shown.

7.Fill the pan with 5 gallons of water. The pump should be sub- merged.

NOTE: For longer pump life, always place the pump in a clean water source.

8.Turn saw on. If lower water flow is desired, use the flow restrictor on the water line.

5

Image 7

Contents Dewalt DEWALT… Built Jobsite Tough EnglishTable of Contents Grounding Instructions Important Safety Instructions for All ToolsAWG Would be 3 76mm or Less from Cutting Wheel Additional Safety Rules for Wet Tile SawStep Quick Start Guide D24000 Wet Tile SawAttach the cutting cart to the rails Steps 5, 6, 7Assembly Fig Features FigTo Attach Cutting Wheel FIG Operation Types of Cuts Figs Locking the Cutting Cart FigAdjustments Fig Accessories MaintenanceBe Sure to Follow Safety Rules and Instructions Troubleshooting GuideDEWALT… DE Conception Robuste Pour LE Chantier FrançaisEwalt Table DES Matières Directives Concernant LA Mise À LA Terre Consignes de sécurité importantes concernant tous les outilsFrançais Français Étape Guide de démarrage Coupe-tuile à l’eau D24000Fixer de la lame Fixer l’établi de coupe aux mon- tants Étapes 5, 6, 7Fixation DE LA Lame FIG Composants àAssemblage à Ensemble du bras moteurFonctionnement Verrouillage de l’établi de coupe fig Réalisation d’une coupe figTypes de Coupes à Réglages à Entretien Contrat D’ENTRETIEN Gratuit D’UN AN AccessoiresGarantie limitée de trois ans LamesQUE SE PASSE-T-IL? Guide de dépannageQuoi FAIRE… DEWALT…PARA Trabajos Pesados EspañolÍndice 120V 15,2 15,2-30,4 Instrucciones DE Conexión a TierraMás No más Reglas de seguridad adicionales para sierras de corte húmedo Español Paso Guía de referencia rápida Sierra de corte húmedo D24000Conecte el carro de corte a los rieles Español Pasos 5, 6, 7Ensamblaje Fig Características FigPara Conectar EL Disco DE Corte FIG Operación Tipos de corte Fig Profundidad del disco de corte FigRealización del corte Fig Bloqueo del carro de corte FigAjustes Fig Limpieza MantenimientoEscobillas Fig Transporte y almacenamientoGarantía limitada por tres años ReparacionesAccesorios Póliza de GarantíaAsegúrese DE Seguir LAS Reglas E Instrucciones DE Seguridad Guía de resolución de problemasD24000